The following code generates an error message when we invoke the assembler. What is wrong (Assume 64 bit machine) movw (%rcx), 4(%rdx) Cannot have immediate as destination Destination operand incorrect size No register with this name Cannot use this register for addresses Mismatch between instruction suffix and register ID Cannot have both source and destination be memory references

The following code generates an error message when we invoke the assembler. What is wrong (Assume 64 bit machine) movw (%rcx), 4(%rdx) Cannot have immediate as destination Destination operand incorrect size No register with this name Cannot use this register for addresses Mismatch between instruction suffix and register ID Cannot have both source and destination be memory references

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write an assembly code to assign the register BX with 4014H, and register DX with 4028 H. Move the content of BX to DX, und verse versa. Then, copy the now value of low content for BX and DX .to memory location [2131 H], and [2139H]
read question carefully
In this case, every instruction receives its own data, independent of how the data for other instructions is obtained. We make advantage of a: A Multiple Data/Instruction B Multiple Iterations of Data or Instruction C Singular Data Single Inst D Singe Inst Multiple
Please explain the difference between Register Direct Addressing and Register Indirect Addressing with proper examples. Please find the Machine code for the instruction: Mov 101A[BP+DI] , DL . Consider the Opcode fora Mov operation to be 10 00 10
In this case, every instruction gets its own data in a way that is completely separate from how the data of other instructions is obtained. We utilize: A Multiple Data/Instruction B Multiple Data/Instruction C Singular Data Single Inst D Singe Inst Multiple
Modern CPUS employ branch prediction in order to: O improve the effectiveness of register forwarding allow multiple instructions access the same register at the same time reduce the latency penalty caused by control hazard O reduce the average latency of fetching each branch instruction
1) For each of the instructions below, assume the initial conditions shown for r3-r5 and the flags. For each instruction, show the value of any registers that are changed. If the instruction affects flags, show the value for all flags that are affected. Initial conditions: r3 = 0XF0E1 D2B3 r4 = 0x1496 3A40 r5 = 0×47CE 811E NZCV = 1010 a) ADCS r4,r3,r4 b) CMP r3,r5 c) TST r4,#0xF d) MVNS r5,r3 e) ASRS r3, r3, #1
Use the register and memory values in the table below for this question. Assume a 32-bit machine. Assume each of the following questions starts from the table values; that is, DO NOT use value changes from one question as propagating into future parts of the question a) Give the values of R1, R2, and R3 after this instruction: sub R1, R2, R3b) What values will be in R1 and R2 after this instruction is executed: lw R2, 8(R1)c) What values will be in R2 and R4 after this instruction is executed: addi R2, R4, 0x0020
Assembler Language VAR1 DS F VAR2 DS 5F Add VAR1 to VAR2. To do this, load both into registers and use Add Register (AR) Reference: Load instruction format: label L R,D(X,B) Add instruction format: label AR R1,R2 No need to write the entire code, just a snippet of above line code, explanation would be nice, thanks
What will be the values stored in registers r1 and r0 after the execution of the instruction mul r16, r17 if r16 and r17 originally contain the following values? (a) 0x58 and 0x37 (b) 0x29 and 0x49
25-
MCQ select more than one