The following code generates an error message when we invoke the assembler. What is wrong (Assume 64 bit machine) movb %cx, 8(%rax) Destination operand incorrect size Mismatch between instruction suffix and register ID No register with this name for one of the operands Cannot use this register for addresses Cannot have immediate as destination co and destination he memory references

The following code generates an error message when we invoke the assembler. What is wrong (Assume 64 bit machine) movb %cx, 8(%rax) Destination operand incorrect size Mismatch between instruction suffix and register ID No register with this name for one of the operands Cannot use this register for addresses Cannot have immediate as destination co and destination he memory references

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Note: solution should use intel 8085 microprocessor Answer a) Microprocessor intel 8085 Q2: Write the assembly code to (No MVI allowed- Assume ALL Registers have 00H initially)! a) Load into registers B through E (in sequence) from memory locations (2EFCH) onward. Let the microprocessor perform the operation B+D then store the answer at (4020H) b) Memory Map Segment 40H 20H 17H 11H 40H 20H 17H 20H 20H 40H 20H 2EFCH 4020H
When taking the question, it would appear as: Write an equivalent assembly code for the following expression (on 32-bit signed data). You cannot modify registers eax and ebx. You are allowed to use only register ecx for intermediate calculations. val1 = (val1 eax)+(val1-ebx) %3D
Please solve and show all work. For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 8-byte words: f = (g+i+2) + (h − 8); B[8] = A[i-9] + A[j+8] + 7;
Convert the given hex value to its R-format MIPS instruction by completing the following table. The instruction and letters for registers must be in lower case. DO NOT TYPE DOLLAR SIGNS WITH REGISTERS. Hex Opcode (decimal) rs (decimal) rt (decimal) rd (decimal) funct (decimal) Instruction 02488822 O 18 16 17 34 sub s4 $$1 " $ to " LA
3. For each instruction in the table, write 8 hexadecimal digits that represent the 32 bits in the destination register after the instruction is executed. Assume s0 is 0x98AB3C6A, s1 is 0x20503666. Instructions to, 50, s1 t1, so, s1 t2, so, s1 t3, 50, 51 addi t4, 50, 0x210 wwwwwww andi t5, 50, -16 add and or xor slli t6, 50, 12 srai s2, 50, 8 Dest. reg. in 8 hexadecimal digits
1) For each of the instructions below, assume the initial conditions shown for r3-r5 and the flags. For each instruction, show the value of any registers that are changed. If the instruction affects flags, show the value for all flags that are affected. Initial conditions: r3 = 0XF0E1 D2B3 r4 = 0x1496 3A40 r5 = 0×47CE 811E NZCV = 1010 a) ADCS r4,r3,r4 b) CMP r3,r5 c) TST r4,#0xF d) MVNS r5,r3 e) ASRS r3, r3, #1
Assembler Language VAR1 DS F VAR2 DS 5F Add VAR1 to VAR2. To do this, load both into registers and use Add Register (AR) Reference: Load instruction format: label L R,D(X,B) Add instruction format: label AR R1,R2 No need to write the entire code, just a snippet of above line code, explanation would be nice, thanks
Develop the assembly code for the following: Load 10 Hex values in 10 memory location. Next find the sum of all the values loaded in the memory location. At the end Register A should contain low byte and Register R5 High byte of the final result.