The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. A Answers: 2.19 kN 0.68 m 2.21 m 63° 0.15 m 0.15 m 670 N-m 1.18 kN kN-m M- i i+ R-( i j) kN

The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. A Answers: 2.19 kN 0.68 m 2.21 m 63° 0.15 m 0.15 m 670 N-m 1.18 kN kN-m M- i i+ R-( i j) kN

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9MCQ: Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated...

See similar textbooks

Similar questions

Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
Q/ In an armature winding of d.c machine, the conductors are connected in Ans/ 1- Series 2- parallel 3- series-parallel combination 4-parallel- series combination
A generator supplies a motor through a Y-A transformer. The generator is connected to Y side of the transformer. A fault occurs between the motor terminals and the transformer. The symmetrical components of the subtransient current in the motor flowing toward the fault are: I =-0.8- j2.6pu I =-j2.0pu I =-j3pu From the transformer toward the Fault: I = 0.8– j0.4pu I? =-j1.0pu 1 = Opu Assume X =X,=X, for both the motor and the generator. (a) Describe the fault type and find the prefault current, if any, in line a. (b) Determine the subtransient fault current in per unit. (c) Calculate the subtransient current in each phase of the generator in per unit taking into consideration the phase shift of the Y-A transformer.
D3 . Below is a time current curve (TCC), showing the damage curve of a transformer. Draw (roughly), where we would want a fuse curve to be to protect the transformer
I need the answer quickly
Q Awave wound Dcseries seng rator has Pesistance oftotal armature eonductors of srand aseris field resis tanee equals to half the arm ature resistanke. A loadof-25-2 connected deross the terminalsof bthe generattor given that the developed Powerintne armatureis 2K w caleulate coPper losses. B612
From the following figure, find the number of 10 lateral ties and tie wire if there are 36 columns with cross sectional dimensions of 60 x 90 cm. at 12.00 meters long per column.
Prove that for Murray loop test 2R₁L R₁ + R₂ Lx
Question:4 A Step-down transformer is given and calculate 5:1 120 V 60 Hz V2 i k2 i. Peak load and D.C. load voltage ii. D.C. Current
i need the answer quickly
In a Dd1 transformer ,___________________ a. LV leads HV with 330 degree b. HV lags LV with 30d egree c. LV leads HV with 30 degree d. LV lags HV with 330 degree
Problem 5 Consider a three winding transformer with the following particulars: = Z₁ Z2 Z3 =0.02 + j0.08 £, V₂ = 400 V, 12 = 60/30° A, and I3 = 50/-40° A. Assume that V₂ is the reference phasor, calculate: The intermediate voltage Vo. a. b. The primary current I₁ and the primary voltage V₁. c. The tertiary voltage V3 referred to the primary side. d. The apparent powers and the power factors at the primary, secondary and tertiary terminals. e. The transformer efficiency.