The figure shows the finishing position of a body builder's arm who is performing a standing lateral raise with a 5.00-kg dumbbell. This is an excellent exercise that isolates the lateral deltoid muscle. The weight of the arm itself is 42.5 N, and it acts at point A in the figure. Given the information shown, and the fact that = 9.74°, (a) find the magnitude of the tension force in the deltoid (F) and (b) the normal force from the shoulder joint (acting on the humerus bone that holds the arm in this equilibrium position. (a) Number i (b) Number i 0.075 m Oe F, 0.250 m Units Units 0.510 m arm <> <> 5 kg

The figure shows the finishing position of a body builder's arm who is performing a standing lateral raise with a 5.00-kg dumbbell. This is an excellent exercise that isolates the lateral deltoid muscle. The weight of the arm itself is 42.5 N, and it acts at point A in the figure. Given the information shown, and the fact that = 9.74°, (a) find the magnitude of the tension force in the deltoid (F) and (b) the normal force from the shoulder joint (acting on the humerus bone that holds the arm in this equilibrium position. (a) Number i (b) Number i 0.075 m Oe F, 0.250 m Units Units 0.510 m arm <> <> 5 kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sled with a mass of 25.0 kg rests on a horizontal sheet of essentially frictionless ice. It is attached by a 5.00-m rope to a post set in the ice. Once given a push, the sled revolves uniformly in a circle around the post as shown in the figure. If the sled makes five complete revolutions every minute, find the force F exerted on it by the cord. R-
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=250 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is γ=6°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=40°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
5. The figure below represents the anatomy of the lower limb when balanced on your toes and the body weight acts through the tibia. The Achilles Tendon makes an angle (0) of 8° with the vertical and for this foot x1 is 6.2 cm and x2 is 12.3 cm. Calf Muscle Tibia Achilles Tendon Calculate the tension (T) in the Achilles Tendon if a 70 kg man stands on the toes of both feet. Using the values in this example what is the mechanical advantage for this lever and describe what that means in terms of the efficiency of the lever.
The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
2. The 6-kg frame AC and 4-kg uniform slender bar AB of length / is free to slide along a smooth fixed horizontal rod. a. Find the tension in the wire BC for a static case where the frame and bar are stationary. b. Now, with the the 80 N force applied find the tension in the wire BC. 60° to Q B 60° -80 N -x
Please help. Please make sure you clearly state how you got the numbers you got and why you are using them. Also please make sure you clearly put your formulas and label your units along the numbers that you are using. In the following frame ilustration, F1s 60 N and F2 is 9 N. What is the tension in the cable AB and the reaction force vector necessary to keep the system in static equilibrium? Give the X component reaction force at C( for an x axis going left to right). Also please solve for the rest of the 3 unknowns please. Thank you
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 1000 lb is applied to the tire at point C at an angle of 0 = 17° as shown. Assume the connection of the wheel to member AB is rigid. 1 h₁ K: LOFF 0 W₁ h₂ h3 h4 h5 B W₁₂ AXHIMAL W4 hs: h₂ cc i❀O BY NC SA 2013 Michael Swanbom W3 - W₁ Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value h₁ 6.6 in W1 7.5 in 16.6 in W2 4.6 in 14.6 in W3 8.3 in 10.2 in W4 6.2 in 5.2 in W5 9.7 in
The cable that suspends the 132 kg mass wraps over the pulley with center C and ties off at E. The pulley has negligible radius. (Assume that the +x-axis is to the right and the +y-axis is up along the page. |132 kg 3.2 m 2.4 m 2.4 m Determine the force that pin A exerts on bar ABC, and determine member force BD. (Enter forces in kilonewtons.) A magnitude kN direction magnitude kN direction magnitude kN sense compression Determine the force that pin C exerts on bar ABC. (Enter the magnitude in kilonewtons and the direction in degrees counterclockwise from the +x-axis.) magnitude kN direction ° counterclockwise from the +x-axis
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB
Pivot A constant density bar with mass m and length Lis held in place as shown. Use the usual x,y,z coordinates for the following questions. Celling Cable 12. Measuring from the pivot, in the space below draw the torque-pic for the weight force exerted on the bar. Be sure your torque-pic includes both an expression for r in terms of L and also the value for the angle between r and weight force. Bar 350 Length = L