The figure below shows a stepped shaft having D = 35 mm, d = 25 mm, and r= 3 mm. The shaft is made from steel with Sut = 450 MPa. The corrected fatigue strength of the shaft is 225 MPa. How many cycles of life can be expected for an alternating stress of 300 MPa?

The figure below shows a stepped shaft having D = 35 mm, d = 25 mm, and r= 3 mm. The shaft is made from steel with Sut = 450 MPa. The corrected fatigue strength of the shaft is 225 MPa. How many cycles of life can be expected for an alternating stress of 300 MPa?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: A round shaft supports a transverse load of F= 15,000 lbf and carries a torque of T = 7 kip-in, as…

Q: A transmission shaft, supporting two pulleys A and B and mounted between two bearings C, and C, is…

A: 45C8Sut=600 N/mm2Syt=380N/mm2kb=1.5kt=1.0θ=5°G=79300N/mm2dA=200mmdB=300mm To-Find:- Shaft Diameter…

Q: Two solid 1.625-in.-diameter steel shafts are connected by the gears shown in the figure. The shaft…

Q: A shaft is made of an aluminum alloy having an allowable shear stress of Tallow=116 MPa. (Figure 1)…

Q: i. A motor driving a solid circular steel shaft transmits 30 kW to a gear at B - Figure 1(b). The…

Q: Given the figure shown below, bronze and aluminum compound shaft are attached to rigid supports. The…

A: To find: The maximum torque carried by the aluminum shaft. Given: The diameter of bronze shaft is…

Q: The compound shaft shown in the figure consists of two steel [G = 80 GPa] pipe segments. The shaft…

A: Given Data:The modulus of rigidity of steel is..The outside diameter of segment 1 is..The wall…

Q: Two solid 1.625-in.-diameter steel shafts are connected by the gears shown in the figure. The shaft…

A: To find:Maximum shear stress in each shaft

Q: yield strength of oy 750 MPa. Determine the design factor of safety using Tresca and von Mises…

A: DefinitionTersca Theory:A ductile material fails or yields when its maximum shear stress equals or…

Q: A solid shaft made of a ductile brass alloy is subjected to an array of loads, resulting in the…

A: Maximum shear stress theory Maximum shear stress theory is also known as Guest's theory. According…

Q: A torsional moment T = 8,867 Nm and a load P = 59,372 N are applied at the same time to a circular…

A: Given data:- Torque (T) = 8867 N-m Force (p) = 59372 N Inner diameter = 49 mm Outer diameter = 70…

Q: 02/ An AISI 1020 Cold Drawn Steel shaft with the geometry shown in Figure below carries a transverse…

A: consider the equilibrium of moment about right support ∑Mright=0 R2 X 315 -7 (140)=0…

Q: A shaft is made of an aluminum alloy having an allowable shear stress of Tallow = 116 MPa. (Figure…

A: Introduction In this problem, we will use the shaft's generalized torsion equation to find the…

Q: If infinite life is not predicted, estimate the number of cycles to failure. ing.

Q: Figure Q1 shows a solid steel shaft AF which is supported by frictionless bearings at B and F. It is…

Q: A compound steel [G= 94 GPa] shaft consists of solid 28-mm-diameter segments (1) and (3) and tube…

A: Shear modulus of the compound steel (G): 94 GPa (or 94 x 10^9 Pa)Diameter of solid segments 1 and 3…

Q: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A: Here is the solution for the above question.

Q: A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a…

A: The factor of safety. FBD: The free-body diagram is shown below.

Q: is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to…

Q: Just Solve a Use Abaqus

A: Abaqus is a powerful finite element analysis software that can be used to solve this problem. Here's…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

This course
EHide blocks
The figure below shows a stepped shaft having D = 35 mm, d = 25 mm, and r = 3 mm. The shaft is made from steel with Sut = 450 MPa. The
corrected fatigue strength of the shaft is 225 MPa. How many cycles of life can be expected for an alternating stress of 300 MPa?
D
M
M
Select one:
O a. N = 3.40E+04

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?