The expressions to calculate the maximum normal and shear stresses for the profile of the figure: b = 0.25m, d = 0.15 m and h = 0

Q: O AF F. p0.2 p0.2 p0.2 S. 0.2-mm (0.2% of 100 mm=0.2-mm)- AL II R.

A:

Q: At a point in an elastic material, ,40 Nimm a direct tensile stress of 80 N/mm and a direct…

A:

Q: A pressure-vessel is fabricated by gluing the circular plate to the end of the vessel as shown in…

A: Internal pressure = P = .45MPa Diameter = d = 450mm Thickness = t = 10mm Side thickness = t' = 20mm

Q: total length of column member, I = 3 m beam width, b = 6" or 150 mm (dressed) beam depth, d = 6" or…

A: Total length of column(L)=3 m Total load(P)=56.25 kN Width of column(b)=6" or 150 mm Depth of…

Q: b 1- Shear failure occur when oz Oh > oy OH > Oy > oh Oy > OH > Ơh 5- Tensile Failure Vertical…

A: Brief concept introduction- Shear failure- It occurs when the shear stress developed in the…

Q: A wire cable was was used to suspend a 500 pound support beam. The orginal length was 12 feet. The…

A: Original length, L=12' Stretched length, L'=12.01' Therefore,  change in length,x=12.01'-12'=0.01'

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: ver a length of 1 m. induced is 120 N

A:

Q: 200KN 200 ku

A:

Q: 3. Consider the given state of stress 40MPA y +, 10MPA → 70MPA 22.5° a) Determine the principal…

A: As per the bartleby guidelines, i am able to answer three sub-parts at a time so I was answered the…

Q: please solve if uktimate tensile stregth is 800MPA. assume reliabilty of 98% fatigue fraction f of…

A:

Q: 50mm (for BC), find the average normal stress in each road and the total deformation of road AB and…

A:

Q: The stress strain diagramfor an unknown material is shown. Determine tha strain at point Y.…

A:

Q: = 5,900 psi, and Tzy = 1,650 psi, (see the figure). Consider only the in-plane stresses (the…

A:

Q: For a square cross-section bar affected by torsional moment at both ends, the streps components are…

A: σx=150σy=100zxy=-60σmaj/min=σx+σy2±σx-σy22+zxy2               =150+1002±150-10022+602…

Q: A solid 11 mm diameter shaft is subjected to an axial load of P-33 kN and a torque of Tacting as…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: to find - absolute maximum shear stress from given principal stresses.

Q: A prismatic bar has a cross-section of 25 mm by 50 mm and a length of 2000 mm. Under an axial load…

A: Width B=25 mm Depth D=50 mm Length L=2000 mm Load P=100 kN Elongation ∆L=2 mm Tensile stress & %…

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

A:

Q: A flexible connectoin consisting of rubber pads (thickness t = 9 mm) bonded to steel plates is shown…

A:

Q: 10. A steel bar of (E) modules of elasticity, is subjected to various end conditions shown in…

A: Schematic diagram of the given problem: Calculate the area at ordinate B: AB=2A+3A-2A5LL=2.2A

Q: I am still confused with the sign convention we were told that in rock mechanic the sigma y in…

A: This question is related to the Stresses transformation from Strength of the material from Civil…

Q: On the free surface of an aluminum[E- 10000 ksi, v= 0.35) component, the strain rosette shown was…

A: Solution: 1) Normal strain at the point associated with axis x and y: We have,…

Q: e state of stress at a point in 2-0 stress system is characterized by direct stresses of40 MPa…

A: Given- Stresses- σ1=80 MPa,σ2=-40 MPa,

Q: B find the max Value of (P) that can be applied on the Cantilever beam Shown in figure, knowing that…

A: Consider the given beam. Calculate the moment in the beam as follows. M=Pcosθ×450=P×35×450=270P N·mm

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: This question is related to the Strength of Material.

Q: CBR Test is carried out to determine the resistance of the subgrade to deformation under the loads.…

A: CBR test is carried out to determine the resistance of the subgrade to deformation under the loads.

Q: Define the below ? Lateral strain is considered – Skempton–Bjerrum method

A: Solution: This is the method in which the settlement occurs in the layer of soil wherepi is…

Q: 9. A titanium T-bar having cross-sectional dimensions shown in Fig.9 is 320mm long and cantilevered…

A:

Q: Crack FIGURE 0xx . . COS 2.7 03, COS 27 K₁ ossin(cos() ਰ - X Stresses near the tip of a crack in an…

A:

Q: A metal block (E60 GPa and Poisson's ratio of 0.35) rests on a rigid surface as shown below. It has…

A: E = 60 GPa = 60x103 N/mm2

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: Find the value of maximum shear stress Rectangular cross sectional area-5 mm2 Shear force=2 N

A:

Q: Show the step by step solution for problem 2-12

A:

Q: In the marine crane link CD is has a uniform cross section of 50 x150 mm and a modulus of 200 GPa.…

A:

Q: (d) Determine the maximum in-plane shear stress. 10 ksi 16 ksi

A: This question is related to Principal Stresses from Strength of Material. In this question we…

Q: Which of following is wrong concerning the extensometer used in a tension or compression test? a.…

A: Extensometer is a device which is used to measure the deformation of the specimen and characterize…

Q: a.)Determine the required gap (δ) so that the rails just touch one another when the temperature is…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.