Which of following is wrong concerning the extensometer used in a tension or compression test? a. The extensometer measures directly the normal strain in the specimen b. The normal strain in the specimen can be calculated after measuring the elongation with the extensometer C. All of the answers d. The extensometer does not measure the normal stress in the specimen

Which of following is wrong concerning the extensometer used in a tension or compression test? a. The extensometer measures directly the normal strain in the specimen b. The normal strain in the specimen can be calculated after measuring the elongation with the extensometer C. All of the answers d. The extensometer does not measure the normal stress in the specimen

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5
Question- Principal stress at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and poisson's ratio=0.3. Find the value of o at the failure when computed by the maximum principal strain theory.
Strength For the state of plane stress shown, determine the largest value of o, for which the maximum in plane shear stress is equal to or less than 75 MPa. After you determine the value, draw Mohr circle for the case
F. A square rod with dimensions 0.02 m x 0.02 m x 0.5 m is attached to a solid surface as shown. If the forces on the rod are too large, it will either crush or be sheared off where it is attached to the solid surface. If the rod can withstand either a maximum normal stress of 25 kPa or a maximum shear stress is 15 kPa, a)what is the largest allowable magnitude of F, (in N) if F,=0? b)what is the largest allowable magnitude of F, (in N) if F,=0? F2
Complete solution please
Give me right solution
At a temperature of 28.42 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 137.38°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 339.61 mm and M=240 mm. Round off the final answer to four decimal places. d ... В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6°C
A 180-mm length of 30 x 40 mm solid rectangular bar is loaded as shown in the diagram. The right end of the tube is fixed to a rigid frame while the left end is free. (a) Draw the stress element for point B at the top center of the bar (right end) and label the stress vectors acting on the element, including the stress magnitudes. (b) Draw the stress element for point C at the middle of the front face of the bar (right end) and label the stress vectors acting on the element, including stress magnitudes
difference between 1st principal stress, 2nd principal stress, and 3rd principal stress in mechaninical engineering
At a particular point in a structural member a direct tensile stress of 60 N/mm² exists on a plane perpendicular to the longitudinal axis of the member while a direct compressive stress of 40 N/mm? occurs on a plane parallel to this axis; in addition shear and complementary shear stresses of 50 N/mm? act on these planes. If Young's modulus E is 200000 N/mm² and Poisson's ratio v is 0.3 calculate the direct and shear strains on these planes and hence, using a graphical method, determine the principal strains at the point, the maximum shear strain and the angle the plane of maximum principal strain makes with the longitudinal axis of the member. Finally, calculate the principal stresses at the point. Ans. E= 3.6x104, ɛ, = -2.9x104, Yy=6.5x10-4 ɛ1 = 4.95x10, 01 = 80.8 N/mm², o1=-60.8 N/mm. Ɛ11 =-4.25x10 Ymax=9.2x10-, 67.5°
Describe a procedure for triaxial testing that raises the deviatoric stress while the nondeviatoric stress remains constant.
At a point on the free surface of a machine component the strain rosette shown in the figure below