The equilibrium position of a block of wood of density 'po' at the interface of liquid 1 and liquid 2 is as shown in the figure. P₁ and P₂ are the densities of liquids 1 and 2 respectively. The ratio of volume of the block in liquid 2 to the total volume of the block is: (a) (c) P₁ P20 Po-P1 P2 - P1 Po - P2 P2-P1 ! Block Po (b) (d) Liquid-1 Liquid-2 Po-P₂ P₁-P2 Po-P1 P1-P2

The equilibrium position of a block of wood of density 'po' at the interface of liquid 1 and liquid 2 is as shown in the figure. P₁ and P₂ are the densities of liquids 1 and 2 respectively. The ratio of volume of the block in liquid 2 to the total volume of the block is: (a) (c) P₁ P20 Po-P1 P2 - P1 Po - P2 P2-P1 ! Block Po (b) (d) Liquid-1 Liquid-2 Po-P₂ P₁-P2 Po-P1 P1-P2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Laminated wood is sometimes used in the construction of highly stressed aircraftcomponents. This wood can be identified by its A. parallel grain construction. B. similarity to standard plywood construction. C. perpendicular grain construction.
Determine the x-bar centroid of the composite figure shown. Where: x=5 ftShow your solution and round off if possible
Question 31 Is the sample in the image softwood or hardwood? 100 O a. Softwood b. Hardwood
3 For a composite bar as shown below, what is the relation between axial deformation and thermal deformations in the bar? Cu tube (1) Steel bar (2) D d- Where, o,, o, = stresses in Cu and steel bar respectively. Coefficient of thermal expansion for Cu and steel bar respectively.
A steel I-beam is suppose to be used as a beam, however, it was found out that the cross section cannot resist the demand. Hence, a steel C-section is added at the top to increase the composite member's capacity against flexure as shown Properties of the 1-beam Flange width-300 mm Flange thickness - 25 mm Web height=200 mm Web thickness-30 mm Properties of C-section Flange width-75 Flange thickness-20 mm Web height 320 mm Web thickness-20mm Using the same steel section above, solve the capacity of a 6-m steel column, fixed support on one end and pin-support on the other. Use Fy = 275 MPa. Assume that the steel section is compact against local buckling Determine the Nominal axial compressive load capacity in KN 7,119.8947 H
A piece of wood floats in water with 15cm projecting above the water surface. When placed in oil, the block projects 10cm above the oil surface. Calculate the height of the wood. O 0.20 m O 0.35 m O 0.16 m O 0.25 m
Bar A-B-C is made from a fully bonded composite of two materials as shown in the cross section below. Find the Z displacement at point C. A C 1.10 m 20 kN B 1.25 m 50 kN с Y I cross section c-c Uz = 5 mm, material 1 5 mm, material 2 5 mm, material 1 25 mm Material 1 E = 240 (GPa) Material 2 E = 180 (GPa) mm (at C)
1. Strength of properly dried wood is significantly higher than that of green (freshly cut) wood. 1. True (i) False
answer quickly
For the composite area shown in Figure 4.1a, determine the y-coordinate of its centroid. Given B = 450 mm, D = 150 mm, t; = 24 mm, tw1 = 30 mm and tw2 = 45 mm. The positive x and y axes of the coordination system are shown in the figure. B D |-tw1+ - twz