For the given composite geometry estimate the moment of inertia about centroidal axis parallel and prependicular to AB. The location of the centroid with respect to point-A: Along x-directlon is: mm. (answer to the nearest'whole number) Along y-direction is: mm. (answer to the nearest whole number) The moment of inertia with respect to the centroid axis: Parallel to line AB is: mm^4. Perpendicular to line AB is: mm^4.

For the given composite geometry estimate the moment of inertia about centroidal axis parallel and prependicular to AB. The location of the centroid with respect to point-A: Along x-directlon is: mm. (answer to the nearest'whole number) Along y-direction is: mm. (answer to the nearest whole number) The moment of inertia with respect to the centroid axis: Parallel to line AB is: mm^4. Perpendicular to line AB is: mm^4.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever of length I, and flexural rigidity El, stiffened by a spring of stiffness k, is loaded by a transverse force P, as shown. 1,EI mm The transverse deflection under the load is
Problem 5 The cantilever beam shown below is non-prismatic and is loaded with a concentrated load at free end B. Determine: a) the vertical deflection at B, b) the rotation at B (use either double integration or moment area) A is ft I₁ = 6000 in 4 10 ft = 3000 in 4 H 20 B K E=29000 ksi
Use the method of virtual work and determine the vertical and horizontal displacement of joint F of the truss. Each steel member has a cross-section area of 300 mm2, E = 200 GPa. 60 kN E 2 m A B 2 m 2 m 2 m
For the truss structure shown, express the position vector r AC from point A topoint C in terms of its components in x and y. Determine the length of truss member AC usingvector operations (i.e., do not simply use the Pythagorean Theorem). Calculate the unit vector forr AC
A beam is subjected to equal bending moments of M. = 3700 N-m. The cross-sectional dimensions are b = 110 mm,c= 32 mm, d = 65 mm, and t = 5 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M. (typ) K b Answer: (a) y= 1 mm mm4 S= mm? (b) OH = MPa (c) OK = 1 MPa (d) Omax = MPa
A prismatic uniform beam has a total length of 4L, a moment of inertia I, and a modulus of elasticity E. The beam is embedded at A, simply supported at B, and subjected to the distributed load q shown. Calculate:a) The reactions and moments in A and B.b) Deflection and slope at point C. You must indicate their directions.
Determine the horizontal and vertical deflections at D for the frame shown below (consider E, I constant and neglect axial deformation). P |2L A В C 4L
Use CONJUGATE BEAM METHOD to Determine the following: A central beam BD is joined at hinges to two cantilever beams AB and DE. All beams have the cross-section shown. For the loading shown, determine the largest w so that the deflection at C does not exceed 3mm. Use E=200 GPa. w 12 mm |A C D E Hinge `Hinge 24 mm 0.4 m 0.4 m 0.4 m 0.4 m
Determine by integration the centroid (?̅) of theshape in the figure (to the right).
Determine the deflection of the static line of the beam in the center of the span and the inclination of the static line in the support B. The beam is made of a material with E = 200 GPa and the moment of inertia of the cross-sectional area is 825 cm ^ 4.
A force of F = {6i - 2j + 1k} kN produces amoment of MO = {4i + 5j - 14k} kN ⋅ m about the origin,point O. If the force acts at a point having an x coordinateof x = 1 m, determine the y and z coordinates. Note: Thefigure shows F and MO in an arbitrary position.
Rod AB is made of steel (E = 29x106 psi), and rod BC is made of aluminum (E = 10.4x106 psi). If force Q = 10 kips, R =5 kips and P = 5 kips, find the deflections of points B and D. %3D 24 in 10 in- 10 in A B C R D 1 in diameter 3 in diameter