Calculate the modulus of rigidity (shear modulus) of an epoxy resin if the modulus of elasticity (Young's modulus) E = 3.5 GPa and the Poisson's ratio = 0.35. Select one: a. G = 1.3 GPa O b. G= 10 GPa c. G = 0.1 GPa Od. G = 3.15 GPa Oe. G = 2.6 GPa

Calculate the modulus of rigidity (shear modulus) of an epoxy resin if the modulus of elasticity (Young's modulus) E = 3.5 GPa and the Poisson's ratio = 0.35. Select one: a. G = 1.3 GPa O b. G= 10 GPa c. G = 0.1 GPa Od. G = 3.15 GPa Oe. G = 2.6 GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the total area of the composite figur e . (mm^2)Determine the x coordinate of the centroid of composite figure. (mm)Determine the y coordinate of the centroid of composite figure. (mm)
y=82 show complete solutions
A composite column is formed by placing a steel bar, 20 mm in diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm, respectively. The column is then subjected to an axial load of 50 kN. If E for steel is 200 OOO N/mm’ and E for the alloy is 70 000 N/mm’, calculate the stress in the cylinder and in the bar, the shortening of the column and the strain energy stored in the column.
IV- It is necessary to design a continuous and aligned glass fiber-reinforced polyester having a tensile strength of at least 1400 MPa in the longitudinal direction. The maximum possible specific gravity is 1.65. Using the following data, determine whether such a composite is possible. Justify. Assume a value of 15 MPa for the stress on the matrix when the fibers fail. Material Glass fiber Polyester Specific gravity 2.5 1.35 Tensile strength (MPa) 3500 50
CN=44
Determine the y-bar centroid of the composite figure shown. Where: y = 18mm and x = 9 mmShow your solution and round off if possible
please need within 30 min thankyou
The first parts of the stress-strain relationships of the components of a randomly oriented composite are shown in Figure P11.25. Estimate the volume percentage of fibers in the composite assuming a fiber efficiency parameter (K) of 0.2. Stress (MPa) 1400 1200 1000 800 600 400 200 I T FIGURE P11.25 0.002 Fibers Strain (m/m) 0.004 Composite Matrix 0.006
A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 230 mm 38 mm 6.5 mm -163 mm- The beam has a cross section of dimensions 150 mm x 230 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 50 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN · m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) (No Response) 14.06 kN· m
A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Taking h= 9 mm and using the data given below, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Brass Aluminum 30 mm Modulus of elasticity Allowable stress h 30 mm h Aluminum 70 GPa 100 MPa The largest permissible bending moment is Brass 105 GPa 160 MPa 1.17 kN-m.
For the composite bar indicated, determine the permissible bending moment when the bar is bent about a vertical axis. Aluminum stress is 100 %3D MPa, Brass stress is 160 MPa, Eb = 105 GPa, Ea = 70 GPa Brass 6 mm Aluminum 30 mm 6 mm -30 30 mm
The trimetallic composite section in Figure 4 is compressed by an axial load P = 12 kN applied through a rigid plate. The section consists of a circular steel core surrounded by 2 brass and copper shells. The steel core has a diameter of 10mm, the brass shell has an external diameter of 15mm, and the copper shell has an external diameter of 20mm. The corresponding modulus of elasticity are Ea = 210 GPa, El = 100 GPa and Ec = 120 GPa.(a) Calculate the compressive stress σa, σl, and σc, in the steel, brass, and copper, respectively, that produces the force P.