The cylinder of weight, W, shown below is being hoisted up with the force F against the vertical wall. If us = 0.57 a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion W or W1 (in kN) = 516

Q: Q3/ The beam is subjected to a moment of 15 kip.ft. Determine the resultant force of the bending…

A: Given: The I section as shown

Q: А 1 F •G d UBC Engineering A group of engineering peasants have constructed a stationary battering…

A: An object in circular motion also develops centripetal force FC=mω2rHere…

Q: A rectangular gate AB in Figure 1 is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric…

A: To find hydrostatic force

Q: For the frame below, F = 9.2 kips, a = 6 ft, b = 5 ft, and c = 3 ft. Determine the magnitude of the…

A: Given: The value of F is 9.2 kips. The value of a is 6 ft. The value of b is 5 ft. The value of c is…

Q: 7. Determine the smallest force P that the worker must apply to the bar CD to prevent the…

A: Step 1: Step 2: Step 3: Step 4:

Q: The coefficients of static and kinetic friction between the crate and the floor are us = 0.3 and μk…

A: Given,  W = 150 lb P = 222 lb Theta = 30°

Q: Determine the minimum force P required to push the crate up the plane. The crate has a mass of 28 kg…

A: The crate is assumed to be stable, then the force applied to move it upward can be calculated by…

Q: Situation 6: Determine the smallest horizontal force P required to lift the 200-kg crate. The…

A:

Q: prevent a load (weight W) from falling downwards. The drum can rotate without friction about point…

A:

Q: P

A:

Q: If the spring is compressed 60 mm and the coefficient of static friction between the tapered stub S…

A: Step 1:

Q: Statics of Rigid Bodies. Thumbs-up will be given. Solve in 4 decimal places. Box the Final Answer.

A: Step 1: Step 2:

Q: The beam in Figure 2 is pin supported at A and roller supported at B. Calculate an equivalent…

A:

Q: Draw the free-body diagram of the hand punch which is pinned at A and bears down on smooth surfaces…

A:

Q: 5. For a fluid at rest, the shear stress is zero. 6. Newton's law of viscosity for a fluid states…

A: As per guidelines we need to answer only 1st question so repost rest question separately

Q: Determine the constant force P required to cause the 0.36-kg slider to have a speed v2 = 0.88 m/s at…

A:

Q: 2. Compute the horizontal force P required to prevent the block from sliding down the plane for the…

A:

Q: 24 mm/s Q2) When the force P is applied to the plate, the velocity profile for a Newtonian fluid…

A:

Q: Knowing that P is 30 kN, applied to both sides of the bar at B and Q is 28 kN, applied to the bar at…

A: Given Data:The intensity of the load P=30 kNThe intensity of the load Q=28 kNThe length of span AB…

Q: 1. The rigid gate with 3m width is installed in order to control the water outflow as shown in the…

A: Given  Width of gate = 3m  Hinge is located 4 m below the top level

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.