Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force ( P ) is required at point B for equilibrium. The weight of the gate is negligible, and C= 4 m J= 3 m E= 2 m e- 60° S.G. of Oil = 0.82 Oil, SG = 0.82 Gate

Q: In the arrangement as shown; Gate 'OA' has width of 2 m inside. Hinge passes through O and rope AB…

A:

Q: A plane truss has a downward applied load P at joint 2 and another load P applied leftward at joint…

A: Given:- To find:- Reaction at roller support Concept:- A truss is a structural element used in…

Q: A 38-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

A: Given data in question Diamond 38 mmLength 3.5 mElasticity modulus 200 GPaCoefficient of thermal…

Q: Consider the frame below, which is supported by a hinge at D and a roller against a vertical wall at…

A: Step 1

Q: Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force ( P) is…

A: Given Data: Specific gravity of oil is So=0.82. Density of the oil is given by: ρo=1000…

Q: Determine the magnitude of the pin force at A. Assume W = 660 lb, a = 2.8 ft, b = 2.0 ft, r = 7 in.…

A:

Q: #11 # 4 65 5m #11 Unit : cm A cantilever beam is shown above. =280 kgf/cm and f, = 4200 kgf/cm³ .…

A: Cantilever beam: A schematic picture of three sorts of cantilever. The top model has a full second…

Q: 1. A steel shaft rotates at 8 Hz with 30 kW taken off at A, 20 kW removed at B, and 50 kW appli at…

A:

Q: 5. Rigid member ABCD is connected to two elastic bars and loaded as shown. Determine the maximum…

A:

Q: Question No. 2 [30%]: Determine the forces in cables AC and AB 1.5 m needed to hold the 20-kg ball D…

A:

Q: bearing at A. Determine the resultant internal loadings acting on the cross section at C.

A: Given:- Total span of shaft = 3m             UDL acting = 800N/m             Point load acting =…

Q: The handcart has a mass of 200 kg and center of mass at G. Determine: [Select] V acceleration of the…

A: Given  P= 50 N

Q: 8. If the pressure remains a constant, then a) Vr1 > Vr2 b) Vr1 < Vr2 c) Vr1 = Vr2 d) Vr1 is a zero

A:

Q: 2) Determine the tension on AB and AC and force along AD for equilibrium of the 350 kg crate. 6.5 m…

A:

Q: Q23: In Figure below find the total pressure force on the gate AB in the two tanks. Assume width of…

A: to find pressure on AB

Q: Determine  Y component of reaction at A Y component of reaction at B X component of reaction at E…

A:

Q: 8. If the pressure remains a constant, then

A: To find: What happens when pressure remain constant.

Q: Problem 6: Determine the contact pressure at point O under the column. тому 2m P=800kN Mox…

A:

Q: The face of a vertical dam has the shape of an isosceles triangle of altitude 4 m with an upper base…

A: Solution

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P- 7…

A: Determine the axial deformation of tapered rod 2 (in mm)

Q: Calculate the member forces of the loaded structure.

A: According to given data Calculate the member forces of the loaded structure.  Given load 60 KN ,  40…

Q: etermine the support reaction Rc, in the simply supported beam shown below. Your answer should be in…

A: Apply equilibrium condition : We apply given three equilibrium condition to solve the support…

Q: Problem 16.3: The temperature of the solid 20mm diameter post CD is increased by 50°C. Determine the…

A: Given, diameter of CD =20mm∆T=50° CI=225×106 mm4Est=200 GPaν=0.32α=12×10-6 /°C

Q: A. Calculate for the axial force in kN at member GK using cantilever method. Enter absolute value…

A: Solve using cantilever method: Assumption: The Point of contraflexure in all member lie at its…

Q: 5) If the weight of block B is 30 lb, determine the maximum weight of block A without upsetting…

A: Given :

Q: Determine the moment of this figure P1=35kN and P2=55kN

A: Given- force values-P1=35 kNP2=55 kNIt is required to determine the moment

Q: 6 m B 60 KN ļº 60 kN P 60 KN 4 panels at 8 m = 32 m EA = constant Sw E Determine the force in member…

A: Given values: Consider the truss given. Using method of joints and method of sections the unknown…

Q: The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position shown,…

A: Given: The unscratched length of spring AB is 3 m. If the block is held in the equilibrium position…

Q: Find the EIy under the 300 N concentrated load in the figure. Use any method.

A:

Q: pinned atone end and supported by two Roads, The beam 20as initially hORLZontal before the load ras…

A: P=120kN

Q: R3 M R, R, X, =1 EI B M CD 1 EI EI CD column M CD A D =1 R, F R, * =1 V=F/2 B Dletete DO00 EI C Mc C…

A: QUESTION : In 1, why if we separate the CD column, all the R1 force is in the column? But in 2, if…

Q: 3. The strength of longitudinal joint is 33 kips/f, whereas for the girth is 16 kips/f. Calculate…

A: Given data in question  Strength of longitudinal joint Strength of girth Internal pressure  To find…

Q: A. Determine the stress at the bottom in the free end. (MPa) 3. Determine the stress at the top in…

A: consider 15 % loss in prestress force

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.