The continuous beam ABC, Fig.2, is of two equal spans L and is loaded with two equal concentrated loads P at the centre of each span. Use the method of consistent deformations to determine the reactions and draw the shear force and bending moment diagrams. (constant EI) L/2 P ** L L/2 W L/2 P L L/2

The continuous beam ABC, Fig.2, is of two equal spans L and is loaded with two equal concentrated loads P at the centre of each span. Use the method of consistent deformations to determine the reactions and draw the shear force and bending moment diagrams. (constant EI) L/2 P ** L L/2 W L/2 P L L/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solve the questions steps by steps and details.
3 Decimal Places 15. Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of the truss system below. Assume A = 1200 mm2, E = 200 GPa. Use a and b from the previous problem. Enter absolute value only. Thank you!
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A= 2.9 in.2. Assume a = 3.50 ft and b=4.20 ft. If the normal stress in each member must not exceed 25 ksi, determine the maximum load Pmax that may be supported by the structure. D Answer: Pmax= i b B b kips
2. Determine the internal forces and draw the diagrams
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
We are given the statically indeterminate structure shown in Figure 2. Apart from the loadings, member AB is also subjected to temperature effects. The cross-sectional depth of member AB is h = 12 in, and the thermal coefficient is aT= 5:10-6 /° F. We are also given that the effect of axial forces on the deformations can be NEGLECTED. 1 kip/ft 5 kip BV VVvvvwwW EI = 8:105 kip-ft2 EI = 106 kip-ft2 20 ft Figure 2 a) Establish a primary structure b) Establish the compatibility equation from which you will obtain the redundant force c) Determine the support reactions of the structure d) Determine the internal loading diagrams of the structure e) Determine the support reactions IF THE STRUCTURE IS ONLY SUBJECTED TO THE TEMPERATURE EFFECTS (and not the loads) AT: = 5 °F ÅT;= -5 °Fi
4. Part AB of the bar has a solid circular cross section and part BC has a hollow circular cross section. The bar is fixed at both ends and a 150-in-kip axial torque is applied at B. Suppose that you want to decrease the weight of the bar by increasing the inside diameter of part B. The bar is made of material that will safely support a pure shear stress of 10 ksi. Based on this criterion, what is the largest safe value of the inside diameter? 4 in 2 in 150 in-kip A -14 in 7 in
Solve using Method of Consistent Deformation
B) The free ends of two cantilever beams each of length L and flexural rigidity El are joined together with a spring as shown in Fig. (6). The stiffness of the spring is K = Using the method of consistent deformations, determine the force in the spring due to a concentrated load W acting at center of the lower cantilever. www
Beam AB is supported as shown in the figure. Tie rod (1) is attached at B and C with double shear pin connections, while the pin at A is attached with a single shear connection. The pins at A, B, and C each have an ultimate shear strength of 57 ksi, and tie rod (1) has a yield strength of 33 ksi. A concentrated load of P = 14 kips is applied to the beam as shown. A factor of safety of 2.4 is required for all components. Determine: (a) the minimum required diameter for tie rod (1). (b) the minimum required diameter for the double shear pins at B and C. (c) the minimum required diameter for the single shear pin at A. 6.7 8 in. 3.8ft (2) 8.5ft
Solve the question with the method of consistent deformations The frame ABC is loaded as shown, determine the support reaction. 5kN/m 5kN/m 4m B 3m