The content of manganese (Mn) in steel was determined spectrophotometrically and with the use of the standard addition method. An unknown sample of Mn from a digested steel sample gave an absorbance of 0.185 when analyzed spectrophotometrically. When 5.00 mL of solution containing 95.5 ppm Mn was added to 50.0 mL of the unknown steel solution (digested sample), the absorbance was 0.248. Calculate the concentration, in parts-per-million (ppm), of Mn in the digested steel sample solution. NOTE: When a problem does not state diluted to a given volume, then you consider the sum of the volumes for Vf. A. 9.55 B. 20.2 C. 5.68

The content of manganese (Mn) in steel was determined spectrophotometrically and with the use of the standard addition method. An unknown sample of Mn from a digested steel sample gave an absorbance of 0.185 when analyzed spectrophotometrically. When 5.00 mL of solution containing 95.5 ppm Mn was added to 50.0 mL of the unknown steel solution (digested sample), the absorbance was 0.248. Calculate the concentration, in parts-per-million (ppm), of Mn in the digested steel sample solution. NOTE: When a problem does not state diluted to a given volume, then you consider the sum of the volumes for Vf. A. 9.55 B. 20.2 C. 5.68

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Related questions

Q: 1 2 3 TEST TUBE 4 5 Blank Unknown solution Volume 0.52 M Fe₂(SO4)3 1.00 mL 2.00 mL 3.00 mL 4.00 mL…

Q: extinction coefficient = ε, path length = b, concentration C A sample containing an unknown…

Q: Calcium in a 100.0 mL sample of fuit juice was analyzed by an electrochemical method that gave a…

A: Any particular substance/compound's quantity either in moles or in mass existing into solution's…

Q: absorbance of 0.467. A standard solution was put through appropriate dilutions to give the…

A: To calculate the percentage of iron in the grass sample, we need to construct a calibration curve…

Q: A student attempts to identify six solutions that contained either hydrogen peroxide (H2O2), calcium…

A: Sequence wise , the answer will be 1. Calcium acetate 2. Lithium permanganate

Q: The concentration of Fe²+ in a sample is determined by measuring the absorbance of its complex with…

A: We would use formula of absorbance given as : A = ECl where, E is molar absorptivity which depends…

Q: To make this KNOWN solution, 0.1632 g was mixed with water (to the mark) in a 100.mL volumetric…

Q: A colored solution of concentration 0.0248 mol/L has an absorbance of 0.353. What is the…

A: The Beer-Lambert’s law, the absorbance (A) is directly proportional to the concentration (c) of the…

Q: The absorption coefficient of O2 in seawater at 0°C is 1.7 mmol/L.What is the concentration of O2 if…

A: Given information, The absorption coefficient of O2 in seawater at 0°C is 1.7 mmol/L.

Q: A 5.0 mL solution containing 3.36 pm Fe(Ill) ions is diluted to 50.0 mL by first treating with an…

A: We must ascertain the concentration of the FeSCN2+ complex generated as a result of the interaction…

Q: The molar absorptivity of a colored solution with a concentration of 0.0222M was determined to be…

Q: Copper was determined in an alloy sample by UV-visible spectrophotometry. The standard addition…

Q: We can determine the copper(II) ion content of a sample using spectrophotometry. The following data…

A: Absorbance is the amount of light absorbed by a substance. The Beer-Lamberts law states that the…

Q: To determine copper in a metallic alloy, 1.245 g of an alloy sample is dissolved in a 1: 2 mixture…

A: The molar absorptivity is determined by substituting 0.505 for A, 750 ppm for c, 1cm for l in…

Q: A standard iron solution was prepared by dissolving 0.0140 g of pure iron in acid then transferring…

Q: Water from Jordan Lake was analyzed for its Fe³+ content. A 20.0-mL sample of lake water was…

A: First, we have to calculate the value of the molar absorptivity constant, ε using the concentration…

Q: Concentration of Manganese in Red Wine 0.6 y = 0.1373x + 0.122 R2 = 0.9986 0.5 0.4 0.3 0.2 0.1 0.5 1…

A: The linear regression equation for the Absorbance versus manganese concentration (ppm) graph is Y =…

Q: A spectrophotometer was calibrated with a 7.236 x 10-4 M (in Cu) Cu-neocuproine solution. This…

A: The question is based on the concept of photochemistry. We need to calculate concentration of…

Q: eq• Calculate Keq-

A: 1. An equilibrium reaction is that reaction which can not go to 100% completion but is at a…

Q: You begin preparation of the calibration curve to measure absorbance vs concentration of FeSCN2+. To…

A: Molarity is the way of expressing concentrations which is defined as moles of solute dissolved per…

Q: To analyze the amount of iron (Fe; Mw = 55.85 g/mol) contained in an ore sample, the sample was…

A: Given in the question, Volume of EDTA = 25 ml Molarity of EDTA = 0.2922 M Total moles of EDTA =…

Q: Determination of the concentration of Zn(II) in a sample of river water was carried out by the…

Q: Why are metals resposbile for the production of colour upon heating

Q: If a second brass washer of 0.6003 grams had been dissolved in nitric acid, diluted to 50.00 mL and…

A: Solution

Q: 0.56 g 1,4‐dimethoxybenzene, 0.9 mL 2‐chloro‐2‐methylpropane, 5 mL nitrobenzene and 0.52 g graphite…

A: The given problem is related to green chemistry. Given: Reactants- Mass of 1,4‐dimethoxybenzene-…

Q: The piperazine content of an impure commercial material can be determined by precipitating and…

Q: Calculate the equilibrium concentration of FeSCN^2 Please explain.

A: Given: Beaker [FeSCN+2] Absorbance 1. 1.6*10-4 M 0.582 2. 1.2*10-4 M 0.448 3. 0.8*10-4 M…

Q: The observed intensity of light (I) after passing through the sample cell is 0.176 of the initial…

Q: Zinc is to be used as an internal standard for the polarographic analysis of thallium. A standard…

A: The objective of this question is to calculate the percentage of titanium present in the sample…

Question

The content of manganese (Mn) in steel was determined spectrophotometrically and with the use of the standard addition method. An unknown sample of Mn from a digested steel sample gave an absorbance of 0.185 when analyzed spectrophotometrically. When 5.00 mL of solution containing 95.5 ppm Mn was added to 50.0 mL of the unknown steel solution (digested sample), the absorbance was 0.248. Calculate the concentration, in parts-per-million (ppm), of Mn in the digested steel sample solution.

**NOTE**: When a problem does not state diluted to a given volume, then you consider the sum of the volumes for \( V_f \).

- A. 9.55
- B. 20.2
- C. 5.68
- D. 140
- E. 22.1
- F. 96.7
- G. 6.95

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

A solution in part C initially contains (4.0300x10^-4) molar SCN¯ and (2.880x10^-3) molar Fe3+. This solution was then measured using the colorimeter, and an absorbance of (4.8600x10^-1) was recorded.The constant determined in part A of the experiment was found to be (3.40x10^3). Using the data provided above, determine the equilibrium constant for the reaction. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: х10 Answer
A solution in part C initially contains (4.06x10^-4) molar SCN¯ and (2.960x10^-3) molar Fe3+. This solution was then measured using the colorimeter, and an absorbance of (4.9800x10^-1) was recorded.The constant determined in part A of the experiment was found to be (3.8200x10^3). Using the data provided above, determine the equilibrium concentration of SCN", [SCN]E in this solution. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer units
Suppose that a solution has an absorbance of 0.250 at a wavelength of 450 nm. If the concentration of the solution is 22 μM, what is the value of the molar absorptivity? The data were taken with a standard 1-cm cuvette. molar absorptivity in (L cm^−1 mol^-1):
What is the molar extinction coefficient at 625 nm for this copper (II) acetate solution? How was it determined? Standard Solution Concentration (M) Absorbance 1 0.025 0.049 2 0.050 0.153 3 0.100 0.242 4 0.200 0.499 5 0.250 0.694
You want to determine the amount of iron(III) in acomplex salt. You make a 100.0 mL solution of the complex salt by dissolving 0.0670 g of complex salt with water to the mark on a 100.0 mL volumetric flask. You get an absorbance reading for the iron from the spectrometer of 0.334. The molar absorptivity is determined to be 17605 L/mole∙cm and the pathlength is 1.00 cm. Determine the molarity of iron(III) in solution. Determine the mass percentage of iron(III) in the complex salt.
A conductance cell was calibrated by filling it with a 0.02 mol L¹ solution of potassium chloride (K = 0.2768 nm) and measuring the resistance at 25° C, which was found to be 457.3. The cell was then filled with a calcium chloride solution containing 0.555 g of CaCl₂ per liter. the measured resistance was 1050 ). calculate( a-) the cell constant for the cell, and (b-) the conductivity of the CaCl₂ solution. C K = G; C 2.9268 C k تو
From experimental data, a plot of absorbance (in arbitrary units, a.u.) at a wavelength of 630 nm (on the y-axis) was plotted against the concentration (in mg/L) of Cu2+ (on the x-axis) in known solutions and a linear relationship was found with an equation of y = 7.22x+0.05. If an unknown solution had an absorbance of 1.20 a.u. at a wavelength of 630 nm, what is its concentration of Cu2+?
Significance of your results: Titanium is also commonly anodized, but does not need to be dyed to achieve colored surface layers. Instead, the color comes from thin-film refraction within the oxide layer - the color is characteristic of the thickness of the oxide layer. Ti²+ (aq) + 2e-Ti (s) E° = -1.60 V TiO₂ (s) + 4 H+ (aq) + 4 e-Ti (s) + H₂0 (1) E° = -1.076 V a. What is the half-reaction at the anode for the anodization of titanium? b. Under standard conditions, what is the smallest potential you would need to provide in order to anodize titanium?