Zinc is to be used as an internal standard for the polarographic analysis of thallium. A standard solution containing twice the concentration of zinc as Thallium has a diffusion current of 1.89 µA for Ti and 3.50 µA for Zn. A 10.0g alloy was dissolved in 500 mL, 25 mL of this solution was mixed with 25 mL of 1.0 x 10-3 M Zn 2+ solution. The diffusion currents of this final solution are 18.2µA for Tl+ and 14.5µA for Zn+. Calculate % Ti in the sample analysed

Q: Purification of chromium can be achieved by electrorefining chromium from an impure chromium anode…

A: According to faradays first law of electrolysis, charge required to deposit cr metal is given by:  Q…

Q: The voltammogram for 20.00 mL of solution that was 3.65 x 10-3M in Cd2+ gave a wave for that ion…

A: Given: Volume of solution=20 mL Concentration=3.65×10-3 M Limiting current=31.3 micro Ampere

Q: Nitrobenzene contained in 310 mg of an organic mixture was reduced to phenylhydroxylamine at a…

A: Given in following question nitrobenzene contain in 310mg…

Q: hours will it take to plate

A:

Q: The standard addition method is used to determine the concentration of vitamin C in apple juice by…

A: Given : Initial volume of sample of apple juice = 2.00 mL Final diluted volume of apple juice = 25.0…

Q: The following cell was found to have a potential of 0.2897 V:SCEIIMg2+(a = 3.32 * 10^-3M)membrane…

A: a) The pMg of the solution is calculated by using following expression.

Q: A domestic water pipe is suspected to be contaminating drinking water with lead. In order to test…

A: Answer is in next part

Q: The conductivity of a 0.05M solution of acetic acid at 18⁰C is 4.4×10-4 (ohms)-1cm-1. Limiting molar…

A:

Q: A steel sheet will have a thin layer of zinc put on one side to protect it from corrosion.…

A: The total charge passed through the solution was Q= It Q= It Q = 2 A ×30×60 Q =3600 C Zn+2 + 2e_  →…

Q: Copper was electroplated from a Cu2SO4 solution onto an electrode with an active surface area of…

A: Given: Surface are of the plate = 7.73 cm2  Density of copper = 8.96 g/cm3  Current passed = 4.54 A…

Q: A 1.963-g sample of an alloy is dissolved in HNO3 and diluted to volume in a 100-mL volumetric…

A: Answer: This question is based on stoichiometric calculation where moles of SCN- needs to be…

Q: A 0.2g sample of toothpaste containing fluoride was treated with 50 cm3 of a suitable buffer…

A: Solution - According to the question - Given - toothpaste sample of 0.2 grams let the amount of…

Q: ELECTROCHEMISTRY: Calculate the required voltage (V) if an unknown metal (M) was electrodeposited…

A: Let voltage required is V volt . And we are given 91%effeicient current = 6.82 ,so nett effective…

Q: A redox titration is performed to investigate iron content in an alloy sample. The potential of…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: 4. The %Mn in steel can also be determined spectrophotometrically by oxidizing the manganese to the…

A: A numerical problem based on analytical process, which is to be accomplished.

Q: A dilute NaNO; solution is to be electrolyzed with a pair of Pt electrode at a current density of…

A: Principle:A spectrophotometric determination using a reaction between nitrite,suphanilamide and…

Q: Calculate the ionic strength of a solution that is 0.040 mol kg−1 in K3[Fe(CN)6](aq), 0.030 mol kg−1…

A: Given  concentration of K3[Fe(CN)6] (aq) = 0.040 mol/kg  concentration of KCl (aq) = 0.030 mol/kg…

Q: was titrated in acidic medium, equal

A: Let molarity of KMnO4=xKMnO4+FeSO4 -> Fe2(SO4)3+Mn2+n=5          n=1

Q: Chemistry In a whole-cell patch-clamp experiment at 32 degrees C, the intracellular solution…

A: In a whole-cell patch-clamp experiment, the reversal potential is defined as the region in the…

Q: An ion-selective electrode for fluoride was investigated. The following results were obtained. Plot…

A:

Q: A student was asked to determine the purity of sodium thiosulfate, Na2S2O3 sample by coulometric…

A:

Q: In electrochemistry, specific conductance is defined as (1000/N)* k, where N is the normality of the…

A:

Q: 116.In a conductivity cell of a cell constant 0.003 cm³¹ concentration of 0.01 M solution of acetic…

A: The degree of dissociation of a weak electrolyte at a given concentration can be calculated by…

Q: Using the calculated (Mg?+] as a starting point, calculate the ionic strength of the solution. Look…

A: Ionic strength is measurement of concentration in a solution. It is a measurement of electric…

Q: 89. The differential pulse polarogram of 3.00 mL of solution containing the antibiotic tetracycline…

A:

Q: Electrochemical solutions of MY and MX2 were prepared by successive dilutions and their resistances…

A: a) The strong electrolyte is MX2 and the weak electrolyte is MY. This can be determined by looking…

Q: Pt / UO22+ (7,90x10-3 M), U 4+ (9,18x10-2 M), H* (1,47x10-3 M) // Fe* (1,28 x 10-M), Fe* (2,84 x…

A: In the given cell apply Nerst equation and determine Ecell  and if Ecell is positive then cell is…

Q: A conductance cell was calibrated by filling it with a 0.02 mol L¹ solution of potassium chloride (K…

A:

Q: lon selective electrode (ISE) is an electrochemical device for the selective determination of the…

A: The Nernst equation is a fundamental concept in electrochemistry used to relate the electric…

Q: 4. A 0.200-g sample of pyrolusite is analyzed for manganese content as follows: 50.0 ml of 0.100 M…

A: Sample of pyrolusite analyzed = 0.200 g Molarity of Ferrous ammonium sulphate=0.100 M Volume of…

Q: A conductivity cell filled with a 0.01 M KCl solution was found to have a resistance of 189 ohms at…

A: (a) Determination of cell constant:      For 0.01 M KCl solution, Resistance =  , Conductivity…