The composition of the liquid in an 29 wt% griffinium alloy at 898 degrees centigrade is (enter the wt% griffinium)

Q: nosition, and mass fraction of each phase, and sketch the microstructur primary a phase and eutectic…

A: Refer to a phase diagram of (Ag-Cu) alloy and use lever rule using a tie line that extends entirely…

Q: Maximum solubility in FCC austenite at 1147 °C is 2.04 wt% 2.14 wt% 14.2 wt% O 0.022 wt% O

A: Maximum solubility in FCC austenite at 1147 °C will be ,

Q: Describe the phases present at the eutectic temperature when the overall composition is x(Cu)= 0.5

A: The detailed phase diagram of Ag-Cu is:

Q: Sketch a phase diagram for two soluble components. Show the melting tem-perature of each element.…

A: The simplest type of phase diagram for any system can be of two components that are soluble in both…

Q: Compute for the composition, in atom percent, of an alloy that consists of 92.5 wt% Ag and 7.5 wt%…

A: Consider the alloy sample has a mass of 100 g. Then according to the problem, the 100 g alloy sample…

Q: Fine pearlite of steel containing 0.45% C can be obtained after Hardening process Full annealing…

A: Introduction: The 0.45 C medium carbon steel is one of the most commonly used structural materials…

Q: The ability to form martensite increases with increasing the critical cooling rate Examples of…

A: 1. If the cooling rate such that, it just touches the nose of TTT diagram is called critical cooling…

Q: 11-42 Cooling curves are obtained for a series of Cu-Ag alloys (Figure 11-33). Use this data to…

A: %Ag Tliq Tsol 0% Ag(100%Cu) 1085oC   8% Ag 1030oC 950oC 20% Ag 975oC 780oC 50% Ag 860oC…

Q: (°C) (liquid) L A

A:

Q: What is the composition in weight percent of an alloy that contains 98 g tin and 65 g lead? What is…

A: weight of the alloy (98+65)=163g weight percentage of Tin=(98/163)x100=60.12 %…

Q: Schematically draw the cooling curves (temperature vs time plots) of a eutectic alloy, a…

A: The entire sample solidifies at one temperature when cooling a material with eutectic composition.As…

Q: Copper (Cu) and silver (Ag) alloys form a binary alloy system that dissolves each other completely…

A: Please find the solution below

Q: 12 1) As the temperature of a metal increases, the vacancy concentration a) decreases b) increases…

A: In crystallography, a vacancy is the absence of an atom or molecule from a position in a crystal…

Q: Q3/ A- What are the important reactions in( Fe-C) system? B- Calculate the activation energy for…

A:

Q: In the binary phase diagram for the Cu-Ni system in the Figure provided: 1. Draw the microstructures…

A: 1. For point A,Only present in the liquid phase.Co = 40% NiWL = 100% Wα = 0 2. For Point E,Only…

Q: 1044 Determine the liquidus temperature, soli- dus temperature, and freezing range for the following…

A: Liquidus Temperature: It is temperature above which material is in complete liquid state. Solidus…

Q: The number of vacancies in FCC nickel is 15 times higher at 1250°C than at 450°C. Find the…

A: Given-Let number of vacancies is denoted by Boltzmann constant To find-The activation energy for…

Q: In an Al casting ingot containing 2wt.% Cu, the content of Cu at grain boundaries has reached…

A: Diffusion in alloy is the process of atoms from various alloy components transferring between each…

Q: H.W. A copper-nickel alloy of composition 70 wt% Ni–30 wt% Cu is slowly heated from a temperature of…

A: Below figure shows the Cu-Ni phase diagram and a vertical line constructed at a composition of 70…

Q: Describe the cooling of a peritectic alloy with the concentration CO and sketch the microstructure…

A: The given figure is-

Q: a. Determine the composition of phases. b. Calculate the amount of phases present in terms of (i)…

A:

Q: a binary phase diagram ( pressure omitted) what is the maximum number of phases that can coexist for…

A: The two components system are called binary system. The restriction on constant temperature and…

Q: ent, of an alloy that consists

A: Atomic% of Cu =5% Atomic% of Pt= 95 % Required Wt% of above elements in alloys

Q: Determine the Miller indices of plane as shown in the figure below

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 5. For 40 wt% Sn – 60 wt% Pb alloy at 150 oC (at point B) as shown in Figure, ii. Calculate the…

A:

Q: 3. For a Pb-10% Sn alloy Determine (a) composition of the first solid to form; (b) liquidus…

A: Given  Pb-10%-Sn Phase Diagram

Q: If 500 g of a 40 wt % Ag - 60 wt % Cu alloy is slowly cooled from 1000°C to just below 780°C: (a)…

A: If 500g of a 40 w% Ag - 60 wt% Cu alloy is slowly cooled from 10000C to just below 7800C; (a) How…

Q: B/ Aluminum (Tm=660 OC) and Silicon (Tm=1410 OC) were fully dissolved in each other in the liquid…

A: Given: The melting point of pure Al with 0% Si, Tal = 660°C The melting point of pure with 0% Al,…

Q: Determine the hkil indices for the plane A in the figure below. Show all your working. h k

A: Given : The diagram is,

Q: Draw thermal equilibrium diagram for the binary alloy system (Si-Au), from the following data:- a-…

A: To Draw :The Thermal equilibrium diagram for the binary alloy system (Given  : The silicon metal at…

Q: The mass fraction of eutectoid cementite in a hypereutectoid iron-carbon alloy (just below its…

A:

Q: Using the following information: ·A binary system of A and B metallic elements, which are partially…

A:

Q: C/ Bismuth (Bi) was melted at 2710C and tin (Sn) was melted at 2320C. Bismuth and ten are formed a…

A: The bismuth - tin phase diagram is given below -

Q: Explain self-diffusion of nickel.

A: The transfer of a chemical from a high-concentration area to a low-concentration area is referred…

Q: What is the composition, in at. %, of an alloy that contains 35g of Cu and 42g of Zn Acu=…

A: Write the expression of the number of moles of Cu.

Q: How would I... Determine the composition of aluminum and silicon (%Al/%Si) to melt the Al-Si…

A: what you are looking for is the eutectic point in a eutectic reaction a liquid phase transforms into…

Q: 1-Pointed all the phases for this type of phase equilibrium diagram. 2-Draw the cooling carves for…

A:

Q: a. Determine the composition of each phase in a Cu-40% Ni alloy at 1300°C, 1270°C, 1250°C, and…

A: a. Determine the composition of each phase in a Cu-40% Ni alloy at 1300°C, 1270°C, 1250°C, and…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.