Describe the phases present at the eutectic temperature when the overall composition is x(Cu)= 0.5 1400-1300-Liquid1200-1100-FcdFcc1000-point900-800-700-600-500-400-3000.0.60.7 0.8 0.90.10.20.3.0.40.51Agx(Cu)Cu

The detailed phase diagram of Ag-Cu is:

Answered: Describe the phases present at the…

Engineering

Mechanical Engineering

Describe the phases present at the eutectic temperature when the overall composition is x(Cu)= 0.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

c) The Cu-Zn phase diagram is shown in Figure 2. i) For a sample of composition 40 wt% Zn and 60 wt% Cu at 700°C, determine: (1) (ii) the composition of the a-phase present at equilibrium the composition of the B-phase present at equilibrium (ii) the relative amounts of both phases present at equilibrium ii) (ii) For a sample of composition 50 wt% Zn and 50 wt% Cu at 700°C, determine what phases are present at equilibrium? (ii) what is the composition of each phase? ii) For a 68 wt% Zn-32 wt% Cu alloy, make schematic sketches of the microstructure that would be observed for conditions of very slow cooling at the following temperatures: 1000°C, 760°C, 600°C and 400°C. Label all phases and indicate their approximate compositions. Compostion (2: In 20 40 60 100 12200 H2000 1000 1800 H1600 400 1200 600 400 600 200 400 100 20 40 60 Conporiton twt% Zro
The mass fraction of eutectoid cementite in a hypoeutectoid iron-carbon alloy (just below its eutectoid temperature) is 0.100. On the basis of this information, determine the composition of the alloy. If it is not possible to determine the composition from the information provided, enter 0. 0.7365 wt% C
A 50 wt% Pb-50 wt% Mg alloy is slowly cooled from 700 °C (1290 °F) to 400 °C (750 °F). (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase? Temperature (°C) 700 600 500 400 300 200 100 2 0 0 (Mg) 560°C First solid (21 wt% Pb) α 20 465°C 5 a + L Composition (at% Pb) 40 10 L a + Mg₂Pb 20 60 Composition (wt% Pb) Last liquid (67 wt% Pb) 30 Mg₂Pb 40 T T L + Mg₂Pb M 18 80 L + Mg₂Pb 70 100 B B+ Mg₂Pb T B + L D T 1200 1000 800 600 400 200 100 (Pb) Temperature (°F)
What is the composition, in wt% Cr2O3, of the liquid phase in an alloy containing 71 wt% Cr2O3 at 2200C?
3) You see Al-Cu phase diagram below and two microstructures (A and B) having the same nominal composition of 3 percent Cu. In these microstructures, matrix is a and spheres refer to CuAl₂ particles. In A and B, the size of big particles are the same. a) For the same volume constant, if we heat treat the both microstructures at T₁ for a long time, is there any changes in both microstructures? If so, what is that? And is the changes the same for both A and B? Is the rate of changes the same for A and B? Draw the final microstructures of A and B if any changes occur you think so. Temperature a AI 2 I 4 a +CuAl2 1 6 Copper,% CuAl2 α
For an alloy containing 20 wt % Ag, refer to the Cu-Ag phase diagram given in the Figure: What is the melting point of Cu in °C? What are the relative amounts(in %) of the existing phases at 900°C? Define the Eutectic point in terms of °C and the composition % of Ag.
Referring to Figure 1, please answer the following [NOTE: SHOW YOUR WORK on Figure 1]:a. provide the specific name for the phase boundary lines denoted by A and B. b. identify the phases present at equilibrium in the phase fields denoted by C, D, and E. c. identify the specific name for the point denoted by F. d. What is the maximum solid solubility of Mg in Al? At what temperature does it occur? e. An Al-Mg alloy (10 wt% Mg, 90 wt% Al) is heated slowly (to insure equilibrium) from a temperature of 200 C: i. At what temperature does the first liquid phase form? ii. What is the composition of the liquid phase at the temperature in part i.? iii. At what temperature does complete melting (no solid phase remaining) occur? iv. What is the composition of the last solid remaining prior to complete melting? f. Using the equilibrium phase diagram of Figure 1, identify the phases present, their compositions, and their relative mass fractions at equilibrium for a 70 wt% Mg – 30 wt% Al…
For the lead-tin system:(a) Determine the proportions of liquid and solid phases for the 40% Sn composition ofthe lead-tin system at temperatures 2500?, 2000?, ??? 1500?. (b) Draw the development of microstructure along the dashed line at points A,B,C, andD.
Silicon having a melting point of 1412°C forms an alloy with aluminum having a melting point of 660°C. The solidification temperature of the alloy is observed to be at 580°C at which the mass fraction of silicon is 0.125 Represent the liquid-solid diagram from the given data. Determine the phases present in the following conditions
Material science Assuming this system forms a laminar type eutectic, determine the volume proportion of phases for an equilibrium solidified 50% Pb alloy. Sketch the expected microstructure.
Q.4) For 30 wt% Sn - 70 wr% Pb alloy at 125 °C, (a) what phases are present? (b) What are the compositions of the phases? (c) Calculate the relative mass fraction of each phase present. Composition (at% Br 100 80 60 40 20 A 3270 Temperature (C) 300 200 100 0 0. (Pb) Solvus Solidu a+L B 18.3 20 liquidus Liquid 183 C 61.9 40 60 Composition (wt% Sn) 80 L 232 C G 97.8 1 600 500 P 400 (3) angesadway 300 200 H 100 100 (Sn)
A 50 wt% Pb–50 wt% Mg alloy is slowly cooled from 700°C to 400°C. (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase?