The coefficient of kinetic friction under block A is 0.30 and under block B is 0.20. Find the acceleration of the system and the tension in each cord. Expected answer: a=4.8ft/s^2 T1=90.91 lb T2=255.36 lb

Q: 18 В 58 7400 N с 18 0.80 m

A:

Q: Blocks A and B in (Figure 1) have a mass of 9.0 kg and 16 kg, respectively. igure #8 -0.4 300 mm AY…

A:

Q: Identical steel bars are used to support a 7400-N load as shown. For the properties of steel bar: A…

A:

Q: 5. A bar which is hinged at its end point and carries a load at its free end, is suppo by two rods…

A: Considering W=6000lb as written in question

Q: The 75-lb force P is applied to the 160-lb crate, which is stationary before the force is applied.…

A:

Q: Question: A rectangular column shown in the figure has fc'=35Mpa and fy=415Mpa. Assuming e=200mm,…

A:

Q: Find the Tension in AC in N.

A:

Q: 20 kg B 4. The coefficients of friction are μ₁ = 0.40 and μ = 0.30 between all surfaces of contact.…

A: Determine the smallest force P required to start the 30-kg block moving.

Q: QUESTION 2 The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter…

A:

Q: Ultimate Axial Force Capacity _______kN

A: The values and diagram given in the question are as follows: Characteristic compressive strength of…

Q: Q6-Determine the maximum force P that can be applied without causing movement of the 90-kg crate…

A:

Q: Question 2 A rectangular plane surface is 3 m wide and 6 m deep. It lies in vertical plane in water.…

A: first draw the figure then find the force

Q: of mass 10 kg and 7 kg respectively, are dined plane and released. The coefficients of tween the…

A: Draw free body diagram of blocks A and B as follows Consider the equilibrium of forces in the…

Q: 2.83 Surface tension can be found by measuring the force to lift a plate: ↑ F W = weight w = width…

A: Using the free body diagram the value of surface tension can be evaluated. Knowing that surface…

Q: A rigid steel bar is suspended horizontally by 1m steel rod at one end and 2m bronze rod at the…

A:

Q: To keep the box from sliding down the plane you applied a certain force P. The box weighs 490.50 N,…

A: To determine the force P required to hold the crate.   Given, Weight of the crate (W) 490.5 N…

Q: Consider (Figure 1). The cord is attached to the 39-lb block, and the coefficients of static…

A:

Q: H.W.1 A steel pipe that contains castor oil (p=1.8624 slug/ft³) is 6 ft in diameter. Determine the…

A:

Q: A solid compound shaft is subjected to torques as shown. The shaft is in rotational equilibrium.…

A:

Q: Dětérmine the magnitude of the force P, acting as shown, that will cause the 120 N crate to move.…

A: Weight of body, coefficient of static friction is given and it has been asked to determine minimum…

Q: 5. A steel bar 50mmx50mm in eross-section is 1.2 m long. It is subjected to an axial pull of 200 KN.…

A:

Q: The uniform 200-lb beam is initially at rest when the forces are applied to the cables. Set F₁ = 140…

A: Weight of the beam, w=200 lb Forces, FA=140 lbFB=240 lb

Q: 2.0 Block A weighs 500.0 N and block B weighs 280.0 N. Block A is held by a cord fastened to the…

A:

Q: The 79-lb force P is applied to the 200-lb crate, which is stationary before the force is applied.…

A:

Q: The 99-lb force P is applied to the 240-lb crate, which is stationary before the force is applied.…

A:

Q: A transmission tower shown below is subjected to lateral loads as shown. A =3.8 kN, B =6.0 kN, C…

A: Determine magnitude of force in member HD in KN

Q: A vertical rectangular gate weighs 6000 lbs and is 10 ft tall and 8 ft wide (into the paper). The…

A: From given data we can draw a free body diagram of gate as shown below:

Q: An axial load of 900 KN is carried by a compound tube comprising of a steel tube and a brass tube.…

A:

Q: For the beam shown, calculate the beam slope at D. A

A: ###Calculation of beam slope at D using unit load method of analysis ##

Q: The coefficient of friction between blocks A and C and horizontal surfaces are µs =0.24 and µk = 0.2…

A: The given figure is shown below:

Q: The same torque is applied to two tubes with identical metal sheets, determine the ratio of…

A: r = 14m S = 19m t = 2.84 Torque = T = same torque is applied on both metal sheets It has been asked…

Q: A laminated plastic beam of square cross section is built up by gluing together three strips, each…

A: Total weight of beam = 3.6 N  Length of beam = 360 mm = 0.36 m  q = total weigth / length  q = 3.6 /…

Q: The 113-lb force P is applied to the 230-lb crate, which is stationary before the force is applied.…

A:

Q: Situation 22: The 125-kg concrete block A is released from rest in the position shown and pulls the…

A: When force is acting on the system or any structural element the two types of reaction are…

Q: Q6-Determine the maximum force P that can be applied without causing movement of the 90-kg crate…

A: