A transmission tower shown below is subjected to lateral loads as shown. A =3.8 kN, B =6.0 kN, C =8.3 kN Determine the magnitude of the axial force in member DH (in kN). DON'T indicate if tension/compression or the sign. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. A-KN 1.5 m K 1.8 m B-kN G 1.8 m C-KN F |1.8 m A 2.55 m 2.55 m

A transmission tower shown below is subjected to lateral loads as shown. A =3.8 kN, B =6.0 kN, C =8.3 kN Determine the magnitude of the axial force in member DH (in kN). DON'T indicate if tension/compression or the sign. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. A-KN 1.5 m K 1.8 m B-kN G 1.8 m C-KN F |1.8 m A 2.55 m 2.55 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
Bronze Steel Steel W = 40 kips %3D 2 ft 2 ft 2.
As shown in figure, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G=42 GPa. Compute the maximum shearing stress in each spring using approximate equation. Steel ww 1 m Steel 50 kg 2m Phosphor Bronze
Pls skip if not familiar and kindy use free body diagram for better understanding. Thank you!
Please explain how they got these values along with the steps used to find them.
Show your complete, detailed, and complete solution. Thank you.
Show complete and neat solution. GRESA FORMAT: Given, Required, Equation, Solution and Answer
SHOW THE DIAGRAM AND YOUR COMPLETE SOLUTION: A statically determinate beam is loaded as shown in the figure below. Determine the following: 1. Determine the shear and moment 5m from point A X A OXDC 30 KN.m 1.5 m Im B 1.5 m C L=6m 10 KN internal hinged 1.5 m 1.5 m ////// E
Q2: A rigid bar is suspended from two wires of equal lengths 250 cm as shown below. Take E,= 210 GPa, E=110 GPa. All data in the Table below. Find: 1. Distance of the load (P) from the bronze wire. 2. Stresses developed in steel and brass wires. - Bronze Wire 250 cm Distance Steel wire Dia Dia Distance P (N) (steel) Сopper between two wires (mm) mm mm 26 35 850 8000
8. Please include FBD & make the solutions understandable
Situation 1: Base on the figure below, the working stresses are 130 MPa for AB and 150 MPa for AC. The cross-sectional areas of AB and AC are 400 mm² and 200 mm², respectively B 25⁰ W 50⁰ C 1. Determine the allowable axial load for wire AC 2. Determine the allowable axial load for wire AB 3. Determine the largest weight W that can be supported by the two wires AB and AC:
A rectangular steel block is 4 inches long in the x direction, 3 inches longin the y direction, and 4 inches long in the z direction. The block issubjected to a triaxial loading of three uniformly distributed forces asfollows: 48 kips tension in the x direction, 60 kips compression in the ydirection, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 ×106 psi, determine the single uniformly distributed load in the x directionthat would produce the same deformation in the y direction as the originalloading. Note provide a diagram/figure. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.