Situation 22: The 125-kg concrete block A is released from rest in the position shown and pulls the 200 kg log up the 30" ramp. If the coefficient of kinetic friction between the log and the ramp is 0.5, compute the following:

Situation 22: The 125-kg concrete block A is released from rest in the position shown and pulls the 200 kg log up the 30" ramp. If the coefficient of kinetic friction between the log and the ramp is 0.5, compute the following:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Will you be able to answer this too please
The 80-kg crate is subjected to the forces shown. If it is originally at rest, determine the distance it slides in order to attain a speed of v = 7 m/s. The coefficient of kinetic friction between the crate and the surface is uk %3D = 0.27. Forces with respect to 45° and 30° are 613 N and 368 N, respectively. %3D |30° 45°
The figure shows the stress condition of an I-section beam at point A. With the Mohr circle method; 1-)Calculate the principal stresses, location and angle. 2-)Calculate the stress components that will affect the plane obtained by rotating the figure counterclockwise 25.
Problem 1: Load P 24 kips compressing the concrete cylinder which length is reduced from 12 inches to 11.9970 inches after compression. The diameter increased from 6 inches to 6.003 in. Determine the value of the modulus elasticity E. = 12 in. de = 6 in -
A composite beam is constructed using a steel plate (10 mm x 165 mm) with two wood beams (75 mm x 165 mm) on either side. The wood and steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M₂ = 7.05 kN m. Steel- Wood = 11 GPa and Es = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention. Use the general theory for Calculate the maximum tensile and compressive stresses in the wood and steel if Ew composite beams described in the textbook.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa maximum compressive stress in wood MPa maximum compressive stress in steel MPa
I need the answer at 15 minute
Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely attached at the lower end. Find the instantaneous stress induced in the bar and its corresponding extension when a weight of 150 N falls on the collar from a height of 60 mm. What percentage error in the stress induced will result if extension of the bar is neglected. Take E 2x 105 N/mm².
A 300-lb block rests on a plane inclined at 36.87° from the horizontal. A 100 Ib force pushes this block up the plane. The coefficient of friction between the block and the plane shown is 0.35. If the block is in equilibrium, determine the maximum friction force that can be developed. A) 63 lb B) 80 lb (C 280 lb D) 84 lb
A 200-lb block is on top of a 300-lb block and both blocks are tied to a pulleya pulley that is attached to the wall, as shown in the figure. The coefficient of static friction between thetwo blocks is 0.3 and between the 300 lb block and the floor is 0.4. The coefficient of dynamic frictionbetween all surfaces is 0.25. Disregard the friction at the pulley.Determine the minimum force that must be applied to the 300 lb block in order for it to initiatemotion (imminent motion).
Question 1 A concrete column 1500mm high is reinforced with 5 steel bars as shown in Figure 1. A compressive load of 2500kN is applied to the column. Given: The diameter of each steel, d, = 40m The diameter of concrete, d. = 500mm The Young's Modulus of steel, E, = 210GPa The Young's Modulus of concrete, E. = 15GPa steel- concrete Force O O O O Figure 1 (a) Calculate the area of both materials (A, and A.). (b) Determine the stress in the steel and concrete (0, and a.). (c) Calculate the change in length of the column (OL) due to compressive load. 6
The 100 kg crate is subjected to the action of the two forces. Determine the acceleration. The coefficient of kinetic friction between the crate and the surface is 0.2. 1000 N 800 N 30°
A 1200 Ibs force acts as shown on a 500 Ibs block placed on a horizontal plane surface. Determine the following: a. Coefficient of friction between the block and the plane surface. b. Determine whether the block is in equilibrium, and find the value of the friction force. If the Coefficient of friction between the block and plane surface are us = 0.30 and Hx = 0.25. 500 lbs 62°- 1200 lbs