The cable is subjected to a force of P (10²) lb. where t is in seconds. (Eigure 1). Figure Silhouette 1 ft tire sensor < 1 of 1 P= (10²) lb Pacesetter Course Ho ▼ Part A 2 Zoom Determine the angular velocity of the spool 3.3 s after P is applied, starting from rest. The spool has a weight of 130 lb and a radius of gyration of 1.30 ft about its center of gravity. Express your answer to three significant figures and include the appropriate units. -Value Submit Request Answer display sett.. 98% Review Units 47:07 PM

The cable is subjected to a force of P (10²) lb. where t is in seconds. (Eigure 1). Figure Silhouette 1 ft tire sensor < 1 of 1 P= (10²) lb Pacesetter Course Ho ▼ Part A 2 Zoom Determine the angular velocity of the spool 3.3 s after P is applied, starting from rest. The spool has a weight of 130 lb and a radius of gyration of 1.30 ft about its center of gravity. Express your answer to three significant figures and include the appropriate units. -Value Submit Request Answer display sett.. 98% Review Units 47:07 PM

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flywheel rotates with a uniform speed of 112rpm for 5.7 seconds .Then it is uniformly accelerated at 0.3rad/s2 for next 7.1 s. then it is made to stop in next 5.4s. Determine (i)maximum angular velocity; (ii) total angular displacement 1.The angular displacement in rad θ1 = 2.The angular displacement in rad θ2 = 3.The maximum velocty in rad/s ω2= 4.The initial velocity in third case in rad/s ω03= 5.The angular displacement in third case in rad θ3= 6.The total displacement in rad θ=
+ G In the above diagram, the wheel starts from rest and rolls without slipping. The force (you don't need the value) causes a constant angular acceleration of 7.112 rad/s2. The radius of the wheel is R - 0.392 m. What is the magnitude of the acceleration of the point at the top of the wheel at time t 1.400 s? This is the point at the outer edge directly above the center of gravity, Gwhere the force F connects to the wheel. Use units of m/s. Don't place units in your answer, 3 o
Q2/ When the mechanism is in the position shown, the velocity of slider D is vp = 1.30 m/s. Determine the angular velocities of bars AB and BD at this instant. _375 B Dimensions in mm 125 225 OSI
Advanced Applied Mathematics - Circular Motion 1. When an airplane touches down at 1 = 0, a stationary wheel is subjected to a constant angu- lar acceleration a = 110 rad/s until / = 1 s. (a) What is the wheel's angular velocity at t = 1 s? (b) At 1 = 0, the angle 0 = 0. Determine 9 in radians and in revolutions at / = 1 s. 2. A small box B of mass mkg is placed on a rough horizontal rotating disc. B is metres from the centre of rotation as shown in Fig. 1 below. The coefficient of friction between the disc and B is u. Find, in terms of u, r and g, the maximum speed v that can be given to B without it slipping. 3. One end of a light inextensible string of length L metres is attached to a fixed point C. A small brass hall Ro
= At the instant shown rod AB has an angular velocity WAB 4 rad/s and an angular acceleration AB 2 rad/s2. Determine the angular velocity and angular acceleration of rod CD at this instant. The collar at C is pin connected to CD and slides freely along AB. = a) using the relative motion analysis and the contact conditions. A 4 rad/s AB= 2 rad/s² WAB 60° 0 = 0.75 m -0.5 m В B D
Pulley C has an inner hub which is fixed to its outer one and turns with it. At the instant wĄ = 7.5 rad/s, pulley A is given a constant angular acceleration α = 32 rad/s². When A rotates 18 revolutions, determine the following: a) Angular velocity we of pulley C b) Angular acceleration ac of pulley C c) magnitude of acceleration of point B on pulley C Wc = 8 WA αA ac = a = 50 mm rad/s rad/s² m/s² A 60 mm B 40 mm
The ends of rod AB (link 3) are pin connected to slider 2 at A and disk 4 at B. The disc is rolling without sliding on horizontal surface. At the instant when 0 = 50°, the speed of A is VA = 3.5 m/s directed to the right. a) Locate, on the figure, the I. C. R. for the rod AB and for the disk. b) Use the respective I. C. R. to find the angular velocities (@3, w4) of the rod AB and disk, respectively. c) Determine, using the I. C. R, the velocity of the center of the disk (point G). Given: r = 0.2 m L = 0.8 m 0 = 50° VA = 3.5 m/s 3 B G
A projectile is shot at an inclination of 45° from the ground with a speed of 250 mps. Determine the radius of curvature after 15 sec. Support your solution with a correctly drawn figure showing the velocity, acceleration and indicate the normal and tangential axes.
position A of the circle disk is at angular position theta=0 and time t=0, disk have angular velocity w0= 1 rad/s when t=0. The angular acceleration of disk is a= 0.2sqrt(w) and a is rad/sec^2. Find vectors of the velocity and acceleration of position A when time = 1 s. Radius of disk r= 1.6 ft.
The radius of the wheel is r=3m. The tangential acceleration is a=2t (m/s2). At t=0, the initial angular position θ0=0 and initial velocity V0=0. After the time of t=6 s, determine (3) the angular position, θ= _________ rad (round to 3 desimal places)
Bar OC rotates with a clockwise angular velocity woc = 5.3 rad/s and a counterclockwise angular acceleration doc = 4.6 rad/s². The bar OC is a slotted member which accommodates the pin A attached to the sector. Determine the angular velocity w and the angular acceleration a of the sector. The angular velocity and the angular acceleration are positive if counterclockwise, negative if clockwise. Assume OA = 500 mm, d = 385 mm, 0 = 21°. Answers: W = B a = i i d aoc rad/s rad/s² @oc
At a given instant the top BB of the ladder has an acceleration aBaBa_B = 2.1 ft/s2ft/s2 and a velocity of vBvBv_B = 4.0 ft/sft/s , both acting downward Determine the acceleration of the bottom AA of the ladder. Determine the ladder's angular acceleration at this instant.