The cable given in the figure is fixed at points A and E with a fixed support and the individual forces given act on certain points of the cable. According to the given: find the support reactions, the part of the cable with the greatest cable tension and its value, and the coordinates of the points where the individual loads act. 1m E 3m D 20N 10N 20N 3m 2m 2m 1m

The cable given in the figure is fixed at points A and E with a fixed support and the individual forces given act on certain points of the cable. According to the given: find the support reactions, the part of the cable with the greatest cable tension and its value, and the coordinates of the points where the individual loads act. 1m E 3m D 20N 10N 20N 3m 2m 2m 1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1 Consider the structure shown below. Determine the tension in the cable and the horizontal and vertical components of reaction of the pin support at A. The weight of the cylinder attached to point C is 80 lb. 5 ft D B₁ -5 ft- -3 ft- C
The frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a ring at B and is attached to hook at G and H. Knowing that the frame supports at point C a load magnitude P = 125 N and weighs 35 N, center of gravity at C, determine the tension in the cable. 0.35 m 0,875 m G H 0.925 m 0.75 m D A 0.75 m В 0.5 m C 0.5 m
A cable stretched between the fixed supports A and B is under a tension T of 2.3 kN. Express the tension as a vector using the unit vectors i and j, first, as a force TA acting on A and second, as a force TB acting on B.
MN=54
Name SURNAME: Student ID: QUESTION 9 The AE cable carrying the concentrated loads is attached to the rod EN, which has two ends of the hinges. The rod EN stands vertically with the cable EG. a = 2 m, b = 8 m, c = 4 m, d = 6 m, P = 20 kN. a) Find the reaction forces at the pins A and G, the force on the rod EN. Draw all the required free body diagrams. b) Find the vertical distances of YAB and yAD- Draw all the required free body diagrams. SOLUTION E- a D HI B P P N P bb-c*c*
Problem 4) Assume the loads applied to the beam result in a uniformly horizontally distributed load 10 k. What is the once transferred to the cable. The loads have magnitudes Pi = 8 k and P2 distributed load acting on the cable w, and what are the vertical support reactions at A and C? E 4 ft l space 8 ft dest A B P1 P2 3 ft 14 ft 8 ft 14 ft 3 ft 8 ft
d PROBLEM 4.26 A rod AB, hinged at A and attached at B to cable BD, supports the loads shown. Knowing that d=150 mm, determine (a) the tension in cable BD, (b) the reaction at A. A D 100 mm 90 N 90 NV B -100 mm --100 mm--100 mm-
Cables CE and BF along with the ball and socket at A support the rigid bar ABCD. (Due to the nature of this problem, do not use rounded intermediate values in your calculationsand answers.) Determine the tension in each cable and the reaction components the ball and socket joint exerts on ABCD at A in newtons. (Indicate the direction with the sign of your answer.) Answer in Newtons TBF= TCE= FAx= FAy= FAz=
Show that, when a frame supports a pulley at A, an equivalent loading of the frame and of each of its component parts can be obtained by removing the pulley and applying at A two forces equal and parallel to the forces that the cable exerted on the pulley. (b) Show that, if one end of the cable is attached to the frame at a point B, a force of magnitude equal to the tension in the cable should be applied at B. A B A в т A A T T T T T т (a) (b) Flg. P6.90
Problem (4) The rod AB is suspended from two rigid cables. When the rod is hanging in th position shown, the forces in the cable are measured to be 6.8 lb at A and 5.2 lb at B. Immediatel after the cable at B is cut, the force in the cable at A is reduced to 3.6 lb. (a) Show that the distance d that locates the mass center G is 6.5 in. (Hint: The rod is at rest before the cable is cut) (b) Determine the angular acceleration of the rod immediately after the cable at B is cut. (Hint: The angular velocity is zero immediately ufter the cut) (c) Determine the mass moment of inertia of the rod about G. 15 in. d A В
Part C Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of d-68.0 with the floor and rope segment CD creates an angle with the horizontal. If both ropes BCA and CD can support a maximum tensile force To 140 lb, what is the maximum weight Was of the crate that the system can support? What is the angle @ required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. ▸ View Available Hint(s) VG ΑΣΦ. Η νοο ?
Problem 4) Assume the loads applied to the beam result in a uniformly horizontally distributed load once transferred to the cable. The loads have magnitudes Pi = 8 k and P2 10 k. What is the distributed load acting on the cable w, and what are the vertical support reactions at A and C? E 4 ft lspace 8 ft A B Ey Ax P1 P2 cy Ay 13 ft 14 ft 8 ft 14 ft 3 ft 8 ft