The bin is 1.5 m wide and is filled with water to the level shown. Determine the resultant force on the side AB and on the bottom BC.

Q: A 5-m diameter open cylindrical tank 10 m high contains sea water. It is made of steel 18 mm. thick.…

A: Given Data Diameter(d) = 5 m Height(h)  = 10 m Thickness(t) = 18 mm Density of sea water = 1023.6…

Q: The compound shaft consists of three segments made from steel, aluminum, and bronze. The shaft is…

A: Given data: A compound shaft consisting of three segments made from steel, aluminum, and bronze.…

Q: The copper pipe [G = 6,000 ksi] has an outside diameter of 3.750 in. anda wall thickness of 0.250…

A:

Q: The

A:

Q: A wooden beam carries the loading shown. Determine the smallest allowable width b of the beam if the…

A:

Q: w = 300 KN Force on the gate, Fw=- CRR Calculate the force, S [kN] due to the stopper (shown) on the…

A:

Q: A vat holding paint( sg=0.80) is 8 m long and 4 m deep and has a trapezoidal vertical ends, 3m wide…

A: The centroid of the trapezoid formula helps to calculate the centroid position of the trapezoid. A…

Q: A polystyrene rod consisting of two cylindrical portions AB and BC is restrained at both ends and…

A:

Q: point D, E, and F on the Assemb 1.25 kN/m

A:

Q: A 5m long, 2m wide and 2m high tank is filled with water.  a. Solve the resultant hydrostatic force…

A:

Q: 2. A 10m high cantilever wall separates water and oil as shown. The water and the oil are 8m and…

A: To find support reaction

Q: For equilibrium, compute the force in part B and its orientation for the given gusset plate. 8 kN…

A: The free body diagram of the given gusset plate is as follows:

Q: (1) 1.6 m B P 2.8 m (2) C

A:

Q: 1. A barrel in the form of a frustum of a cone with a radius of 3m at the bottom and 6m at the top.…

A: Density of oil = 0.85*1000 = 850kg/m3

Q: SECTION: 500mm 20 KN 15 KN/m 1000 mm P: 800 KN e = 400 mm (A SSUME I5 % LOS SES) A. Determine the…

A: Given data  P = 800KN e = 400mm Losses = 15 %

Q: 6. A 50-mm diameter bar is used as a simply supported beam 3 m long. Determine the largest uniformly…

A: Given data in question  Length 3m beam Diameter 50 mm Flexural stress 50 MPa To find out  Value of…

Q: 3. Two 10-in 15.3-lb channels are welded together as shown in the figure. Compute the value of ,.

A: Channel 2 centroid be at the origin Q(0,0)  Channel 1 centroid be at 0.64" below from top of the…

Q: gate

A:

Q: The forms are held in place with the ties between vertical braces spaced every 60cm. The height…

A: bArea of face =0.6m×28mCentroidal distanceh =h2=282=14mso,Force on bottom tie is…

Q: # 4] The isosceles triangle gate shown in the figure is hinged at A and weighs 1000N. What is the…

A: Force exerted by liquid resting on any adjacent body is known as hydrostatic force and the point on…

Q: Two identical steel [E = 200 GPa] pipes, each with a cross-sectional area of 2500 mm2, are attached…

A:

Q: A. Calculate for the shear Force in kN at member ED of the frame shown in figure 1 using Portal…

A: Given data:

Q: The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making…

A:

Q: 503. A cantilever beam, 60 mm wide by 200 mm high and 6 m long, carries a load that varies uniformly…

A: Solution

Q: Refer to the previous problem. Determine the hydrostatic force acting on the plate at this position.…

A: To find out the hydrostatic force acting on plate at this section.

Q: 2 ft В seawater (SG = 1.03) 10 ft P 45° A

A: Weight of gate, W =600lbWidth of gate, B =20ftConsider unit depth of gate .Angle of gate with…

Q: A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 617 lb as shown. The…

A:

Q: 1. A solid steel shaft 3in in diameter and 4ft long is fixed at one end and free at the other, as…

A:

Q: A 2m x 2m gate is inclined 45° from the horizontal. The upper portion of the gate is 1.5 m below the…

A: Compute the hydrostatic force on the gate.

Q: A.) A 24in. Long rod floats vertically in water. It has a 1 square inch cross sectional and has…

A: Note:- According to Bartleby guidelines In case of multiple different question we have to gave…

Q: A vat holding paint( sg = 0.80 ) is 8 m long and 4 m deep and has a trapezoidal vertical ends, 3m…

A: The centroid of the trapezoid formula helps to calculate the centroid position of the trapezoid. A…

Q: Refer to the illustration below. ?′?=28 MPa, ??= 400 MPa. Answer all subparts: a. Determine the…

A: A spiral column is given, need to find out  1.axial capacity 2.spiral pitch 3.clear spacing between…

Q: 4m seawater (SG=1.031) A 60 2m

A: