6. A 50-mm diameter bar is used as a simply supported beam 3 m long. Determine the largest uniformly distributed load that can be applied over the right two-thirds of the beam if the flexural stress is limited to 50 MPa. (Assignment) R₁ = (2/3) w w N/m 3m R₂ = (4/3) w

6. A 50-mm diameter bar is used as a simply supported beam 3 m long. Determine the largest uniformly distributed load that can be applied over the right two-thirds of the beam if the flexural stress is limited to 50 MPa. (Assignment) R₁ = (2/3) w w N/m 3m R₂ = (4/3) w

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A solid steel shaft supports loads PA=490 N and PD = 400 N, as shown. Assume L₁ = 180 mm, L₂ = 620…

Q: Problem #2. The steel rod is stress-free before the axial loads P₁ = 150 kN and P₂ = 90 kN are…

Q: A stress element i's shown in Figure, ueing Mohr's circle. Find the principal stresses and the…

Q: A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure).…

A: Using the assumption that load is shared equally by all columns. The allowable load can be found…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 2900 mm² and an…

A: Given:- Area A1 = 2900 mm2 Normal stress in bar 1= 70 Mpa Area A2 = 2050 mm2 Normal stress in bar…

Q: A 86-N-m torque is applied to a hollov section shown. Neglecting the effect determine the shearing…

Q: P3 P, P2 A 5-m long, simply supported beam is loaded as shown. Determine the lightest W-shape beam…

A: Given, There is a simply supported beam which is Loaded with point load and Udl as shown in the…

Q: 2. Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa).…

Q: A steel column with the cross section shown has a 14.7-ft effective length. Using Allowable Stress…

Q: The beam shown below with a length L = 20 m and a rectangular cross section that has a width of b =…

A: To Find :- Load P

Q: From the given figure below : A. Compute the bending stress in the beam, in MPa, shown in the figure…

Q: The cross-sectional dimensions of a beam are shown. The internal bending moment about the z…

Q: A W410 x 60 standard steel shape is used to support the loads shown on the beam in the figure.…

A: P= 132kN,w= 24kN/ma= 3mb= 2mFree body diagram of beam:-

Q: 16 kN 60 12 70 Ölçüler mm cinsindendir.

A: Finding out stress at point A.

Q: A = 2000 mm² A = 900 mm² B 503 mm 257 mm 355 mm The steel rod is stress-free before the axial loads…

Q: A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor…

Q: 2-22. The triangular plate is fixed at its base, and its apex A is given a horizontal displacement…

Q: A uniform structural tubing column AB with a height of 4 m has a cross section as shown in Figure…

A: The given data is shown below: Height=4mE=200 GPaA=2285 mm2r=37.5 mmI=3.33×106 mm4F=2e=18.75 mm

Q: Question 2) In the system given in the figure, a distributed load of w=76 kN/m acts on the rod AB of…

Q: A compression load of P = 40 kips is applied to a 4 in. by 4 in. square post, as shown. Determine…

Q: Shear Stress H.W W= 1o kN/m 5m Taz ? ,こ?

Q: AW310 x 38.7 standard steel shape is used to support the loads shown on the beam in the figure.…

Q: A cantilever beam with length L = 4 m carries a uniform load w = 33 kN/m. The beam has a rectangular…

A: Given, In a cantilever beam, Length of the beam, L= 4m Uniform load, w= 33kN/m Cross section: b=…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given: The value of d is 50 mm. The value of P is 85 kN. Consider the figure,

Q: *2-24. The triangular plate is fixed at its base, and its apex A is given a horizontal displacement…

A: The triangular plate with dimensions as shown in the figure below,Horizontal displacement,…

Q: Given: A beam has b = 3in and h = 6in, Pa = -6 kips and Pb = -12 kips Determine: Normal stress at…

Q: A simple beam 4.4 m in span carries a concentrated load of 316 kN at its midspan and is subjected to…

A: L = 4.4 mw = 316 kN P = 243 kN Fy = 248 MPa

Q: A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown.…

Q: Consider a square bar 30 mm on side and 2.5 m long, having a material yıeld point 254 (IH MPa). An…

Q: A simply supported wooden I beam AB (shown below) is loaded by the distributed force q = 1.9 kN/m.…

A: Given data:

Q: MA

Q: Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel…

Q: Q1/ A beam has cross section as shown, it is subjected to a shear force of V 200 kN and a bending…

Q: The beam shown below with a length L = 16 m and a rectangular cross section that has a width of b =…

A: Find reactions:∑ MR=0R1L-PL-x=0R1=13P16

Q: 8.5 an 250 kN 250 kN 250 kN B D E 0.9 m'0.9 m 0.9 m 0.9 m Fig. P8.5

A: (a)select the most economical metric wide-flange shape that should be used to support the loading…

Q: 1. Determine the "t" parameter of cross section of the beam in the figure below se Navier formula)…

A: A structure is a structure or an assemblage of related elements that is used to aid a pile.…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

Q: A wood beam carries the loading shown n the figure. Determine the smallest llowable width b of the…

Q: Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that…

A: The tensile stress is defined as the ratio of the applied load in the direction of increasing length…

Q: The beam shown below with a length L = 13 m and a rectangular cross section that has a width of b =…

A: To Find :- load value of P

Q: Your answer is partially correct. A simply supported wood beam that is 13.5 m long carries a 39 kN…

A: Hey there, There is a simply supported beam given in the question and it is subjected to a point…

Q: If P = 8.571 kN, determine the stress in member CE assuming that the area in steel is 24 mm^2.

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

Q: A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three…

A: Calculate (a) the normal stress in each rod. (b) the vertical deflection of the rigid bar at F.

Q: Part a and part b

A: Given data in question Load wSpan LCantilever beamInner radius 50 mmThickness 10 mmLongitudnal…

Q: 2-23. The triangular plate is fixed at its base, and its apex A is given a horizontal displacement…

A: The triangular plate with dimensions as shown in the figure below,Horizontal displacement,…

Concept explainers

Pressure and Stress

Question

6. A 50-mm diameter bar is used as a
simply supported beam 3 m long.
Determine the largest uniformly
distributed load that can be applied
over the right two-thirds of the beam
if the flexural stress is limited to 50
MPa. (Assignment)
1m
R₁ = (2/3) w
3 m
w N/m
↓↓↓↓
R₂ = (4/3) w

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the maximum compressive bending stresses in the beam shown. Let P = 16
A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three rods. Rods (1) and (2) are 16-mm- diameter stainless steel rods that have an elastic modulus of E= 185 GPa. Rod (3) is a 23-mm-diameter bronze rod that has an elastic modulus of E= 100 GPa. Use a = 1.4 m and L = 2.6 m. For a load magnitude of w = 30 kN/m, calculate (a) the normal stress in each rod. (b) the vertical deflection of the rigid bar at F. (1) B Answers: (a) 0₁ = i (b) VF = i a D 2 2a W E F MPa, 0₂ = mm IN i MPa, and 03 i MPa
A channel-section has the dimensions as shown. Consider a cantilevered beam subjected to an end force P. L = 100 cm a) iif cross-section las is used, determine its normal stress distribution. (a) (b) b) if you stack two las sections as a box, but leave a gap between them, two sections carry = loadings with the same distribution pattern. Try express the results. (C) 2ª L 2CM дом E 2ch weld
Q. Som
Tb = 80.51
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
PROBLEM No. 2 The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. If a 20-kip load is applied, determine the vertical displacement in the bar at A and C that will cause a stress in the rod at C to be 50 ksi. Indicate the direction of movement. Use E = 29x106 psi for steel. (Provide FBD and movement diagram in your computation). A = 0.5 in.? 3 ft | A B D | 20 kips te 2 ft -→-- 2 ft -→l 4 ft 4 ft A = 0.75 in.²
Q.3.L
A cube of side 100 mm is subjected to an axial compressive load of 200 kN. Its lateral strain is prevented by applying uniform pressure but only one fourth of lateral strain could be prevented, then which of the following statements is/are correct? Assume E = 200 MPa and μ = 0.3. A The decrease in length in direction of load after applying pressure is 9.358 x 10-3 mm. B The uniform pressure applied has a value of 8.57 N/mm². C The uniform pressure applied has a value of 2.14 N/mm². D The increase in length in lateral direction after applying pressure is 2.25 x 10-³ mm.
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0.0). After load P is applied. joint B moves to the coordinate position (0.35 in., -0.55 in.). Assumeo - 11 ft, b-7 ft, and h-8 ft. Determine the normal strain in each bar. Answers: CAB EBC 3676.02 i 5685.14 με με