The bent rod is supported as shown in the figure by a smooth surface at B and by a collar at A, which is fixed to the rod and is free to slide over the fixed inclined rod. Suppose that F = 120 lb and M = 400 lb⋅ft.  a) Determine the magnitude of the reaction force on the rod at B. b) Determine the magnitude of the reaction force on the rod at A.  c) Determine the moment of reaction on the rod at A.

Q: The figure above is a truss supporting the deck of a bridge. a) determine the support reactions.…

A:

Q: Q1-A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a wall…

A: Given that, Weight of ladder = 250 N Tension force in the string = 50 N Reaction at A = 1.3 kN =…

Q: Two masses are attached to a uniform meter stick as shown in the figure below. The masses of m1 and…

A: Given, m1 = 50 g = 0.05 kgm2 = 75 g = 0.075 kgmstick = 150 g = 0.15 kg   From masses, weights can be…

Q: Find the external reactions. x Z A 6 ft F = 80 lb C 1.5 ft B 1.5 ft

A: Dear student,                      According to the guidelines, I am allowed to answer only one…

Q: Problem 2. Considering a 20 kg bar as shown in the figure: a) find angle theta and the reactions to…

A: Consider NA as the reaction at point A, NB as the reaction at point B, fB be the frictional force…

Q: A) Determine the reaction forces of a rigid plate. To check the solution you will need to specify…

A:

Q: A red pickup track towing a white trailer via a ball-and-socket joint at D. a) Find the reactions at…

A: Taking this part Applying the Equilibrium condition ∑nMA=0…

Q: Problem 6 A 100-lb force P is applied at Point A of a structural member. Compute the reactions at…

A: P=100-lb, The force P is applied at Point A of a structural member.Compute the reactions at the wall…

Q: Problem 2) A pipe configuration is presented in the figure below. The support at point A is fixed.…

A:

Q: 2. A truss is shown in the figure below. a) Based on the number of joints and members, discuss about…

A:

Q: Problem 3.5 - Given the cable tension T = 80 lb, determine a) the moment about point A due to T, and…

A:

Q: A block of mass 40 kg is resting on an inclined surface as shown in figure 4. A) Draw the free body…

A: Given:- M=40kg Angle = 25 degree To find:- a) Free body diagram of block b) Conditions for static…

Q: 2. For the crank-slider machine shown below, the collar at A is frictionless. The vertical applied…

A:

Q: 3) For the following system, the rod is uniform and weighs 1200N and the sign weighs 2000N. The…

A: Given dataDraw FBD

Q: The curved gate in Figure 3 is a 90º arc and is pivoted at O. It has a uniformly distributed mass of…

A:

Q: Q1-A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a wall…

A:

Q: (question 1)          P = 75 lb. The pin at C is attached to member ABCD and passes through the…

A: Given data :- P = 75 lbDetermine :-Part A) Determine the horizontal and vertical components of force…

Q: The crane BC shown below lifts a load of W. Neglecting the weight of the crane. Determine the…

A:

Q: Find the reactions and roller A and pin B А 3 kN 30 3 m 4 m b) Draw the free body diagram

A:

Q: As Engineer, you have been asked to calculate only the forces in the members (AB, AC, BC, and CE) of…

A: The free-body diagram of the truss is shown below. Here, VA denotes the vertical reaction at point…

Q: B. A C. 75

A: Given that, Mass of the cylinder A, mA=200 kg,Mass of the cylinder B, mB=100 kg,mass of the cylinder…

Q: a) Draw a free body diagram of bar CBD. b) Determine the spring force, the tension in cable AB, and…

A: (a) Draw the free-body diagram of the bar CBD.

Q: in the figure below weighing 99 kg/m^2, is lifted slowly by the cables AC and BC. For equilibrium,…

A:

Q: A motorized cable car weighs 1 MT, carrying a loadP is traveling along a straight horizontal cable…

A: given; ⇒mass of car (m)=1MT                  =1000kg⇒weight of car (w)=mg…

Q: A mass of M-kg and length L meters is connected to a wall by a hinge and is free to rotate. There is…

A:

Q: h) The figure below shows a beam supported at points A and B. The vertical force at F is 500 N and…

A: In this issue, we will determine the distance (s) necessary to balance the beam by first calculating…

Q: 4.1 Calculate the magnitude and direction of the reactions at support A and B using the moment law.…

A: for solution refer below images.

Q: Problem 2) A pipe configuration is presented in the figure below. The support at point A is fixed.…

A:

Q: Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In…

A:

Q: 2.00 m D 2.00 m 1.00 m A C E F 1.00 m В 1.00 m 1.50 m 1.80 kN N

A: A Free body diagram isolates the given body from all its supports and shows all the forces acting on…

Q: Q2: The cylinder A weighs 660 N and it is supported by the vertical smooth wall and the cable system…

A: Given Weight of the ball = 660 N To find Tension at AC

Q: 4 in- 4 in- 20 lb 40 lb B 2 in. 3 in. 3 in. E 1. The bracket is supported by pegs at C and D and a…

A: Solution; let the equivalent force acting at x distance from point A.  60×x=40×8x=326=163in

Q: It was known that there are five members concurrent at joint A isolated in the figure below. Out of…

A:

Q: 2. The frame shown below is loaded with an unknown horizontal force, P. At point E, the surface…

A:

Q: A rigid beam loaded with negligible mass is pinned at B and is supported by two identical rods,…

A:

Q: Find the forces in the cables AB, BC, CD, DE, and force in the spring CF in terms of P. (a is an…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.