2.00 m D 2.00 m 1.00 m A C E F 1.00 m В 1.00 m 1.50 m 1.80 kN N

Q: The member (shown to the left) is subjected to the force at the lower right corner, and is…

A:

Q: 2. Draw the FBD of the given 3D system. Solve for the equations of equilibrium. Determine the…

A:

Q: As shown in the image, a 63-kg crate is supported at equilibrium. the angles will be given in a…

A:

Q: 2. A rectangular is supported as shown below. The weight of the plate can be neglected. The plate is…

A:

Q: Lamis theorem is helpful to find the unknown forces acting at a point for a body in equilibrium.…

A: Lamis theorem  It states that when three forces acting at a point in equilibrium system, then the…

Q: Situation 4: Determine the support reaction at A? * 390 lb 1312 800 lb - ft 8 ft -4 ft- 3 ft 30% B

A:

Q: Draw a complete free-body diagram for the system. Calculate the reactions at both supports needed…

A: i) Free body diagram where, RA= Vertical reaction force at A            RC= Vertical reaction force…

Q: hat is the magnitude of F2? (kN)

A: According to the condition of equilibrium, the net force at the joint O in any direction should be…

Q: 1. Fig. 1 shows a simple six bar linkage held in static equilibrium while a force P= 750 N is…

A:

Q: Cable AB passes over the small ideal pulley Cwithout a change in its tension. What length of cable…

A: Given:  m= 75 lb θ=41o Tension T in cable CD=? Cable AB passes over the small ideal pulley C without…

Q: 1. Plate ABCDEF is a sliding door supported by a frictionless linear bearing at A and a frictionless…

A: The total weight of gate is

Q: A uniform plank 8 ft long is balanced on a corner If using a horizontal force of 75 lb as shown in…

A: Let's draw free body diagram of 'AB' as shown in figure. Here, W=45 lb

Q: Find the reaction force at points A, B, and C necessary for member ABC to be in equilibrium. A 5m…

A: Given-

Q: For a 3-dimensional free-body diagram, when all of the forces pass through one point as shown in…

A: ▪︎When the line of action of all the forces passes through the one single point, then it is known as…

Q: Two farmers are pushing on a gate with forces Fa and FB, applied at locations A and B respectively.…

A:

Q: The x-components of three vectors are Fx, +350 lbf, and -118 lbf. If they are in equilibrium, what…

A:

Q: Determine the magnitude of the force PP required to hold the 140-lblb weight in equilibrium

A: GivenW=140lb

Q: Determine the angle (0), and the reaction forces located at A and H. Use the method of sections to…

A: As per our guidelines we are supposed to answer first three sub-parts. The diagram for angle is…

Q: The spring in Fig. is unstretched when e = 6 = 15°. Find the angle 6 for equilibrium if mg = 60 kg,…

A: x=stretched distance ;x-x0=1sin θ-1sin 90×L ; L1=distance from mass at d to at point A ;L2=distance…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.