The beam shown below with a length L = 13 m and a rectangular cross section that has a width of b = 50 mm and a depth d = 150 mm, has a load applied a x = 4 m away from the left hand support. What is the maximum load P that can be applied on the beam if the maximum bending stress can't exceed 14.0 MPa. Ignore any load factors or strength reduction factors. Cross Section: b L

The beam shown below with a length L = 13 m and a rectangular cross section that has a width of b = 50 mm and a depth d = 150 mm, has a load applied a x = 4 m away from the left hand support. What is the maximum load P that can be applied on the beam if the maximum bending stress can't exceed 14.0 MPa. Ignore any load factors or strength reduction factors. Cross Section: b L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hello Bartley Team, kindly look at this question. Why Tutor reject the question without reading. Tutor said its multiple Question. But Here is only 1 question Provide STEP BY STEP HANDWRITTEN SOLUTION
4. Show your complete solution.
The beam shown is made of a nylon for which the allowable stress is 24MPa in tension and 31MPa in compression. Determine the largest couple M that can be applied to the beam. 24 mm 60 mm 30 mm 80 mm
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp
please recheck your final answer.
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 130 kN, w = 27 kN/m, a = 2.8 m, and b = 2.0m. Determine the magnitude and location of the maximum bending stress in the beam. A max = x = a i i B a → Pin |C * b W MPa m D a E
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.4 from the support. (MPa) Properties: Beam width - 211 mm Beam height = 414 mm Pu 73.09 kN Span of the beam = 10 m Prestressing force = 509 kN eccentricity = 130 mm
The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses, in the steel and wood, respectively. If the moduli of elasticity are E {s} = 209GPA and E {w} = 11GPA (Disregard the weight of the beam) Steel 50 mm 50 kN/m Wood B Steel 50 mm 4.0 m- 150 mm 250 mm