The beam-column in the figure is a member of a braced frame. Use LRFD and determine whether this member satisfies the appropriate AISC interaction equation. Endpoints are pin connections in both x and y directions and the member is laterally supported at both ends. The load and moments are computed from service loads, and bending is about the x axis. Use Lp = 3.166 m, Lr: = 12.487 m and Cb as 1.0. The steel is S355; Fy = 355 MPa, Fu = 510 MPa, E= 200 GPa. 450 kN 300 kN 1 m 2 m 4 m 300 KN HE300B 1 m 450 kN

The beam-column in the figure is a member of a braced frame. Use LRFD and determine whether this member satisfies the appropriate AISC interaction equation. Endpoints are pin connections in both x and y directions and the member is laterally supported at both ends. The load and moments are computed from service loads, and bending is about the x axis. Use Lp = 3.166 m, Lr: = 12.487 m and Cb as 1.0. The steel is S355; Fy = 355 MPa, Fu = 510 MPa, E= 200 GPa. 450 kN 300 kN 1 m 2 m 4 m 300 KN HE300B 1 m 450 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Apply the force method to find the internal forces of the truss shown below. E=30,000kips/in² and L(ft)/A(in²)=2 for all members. Assume that B C d D b 3 at 12 ft 90%
Statically indeterminate 2-span beam (as labeled Element 1 and 2) is shown below. Assume EI is constant for all members. Construct: (a) the element stiffness matrix for elements 1 & 2 then construct (b) the structure (global) stiffness matrix and finally (c) partition the global stiffness matrix. All degree of freedom must be properly labeled. 6 k/ft. 5 k A Roller. ORoller Fixed Fixed 15 ft. 10 ft. 5 ft.
A beam is subjected to equal bending moments of M₂ = 3300 N-m. The cross-sectional dimensions are b = 190 mm, c = 26 mm, d = 75 mm, and t = 5 mm. Determine: (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M₂ N y| M₂ (typ) Z- b H K d
Question Three The three-bar truss ABC shown in the figure part a has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm² and modulus of elasticity E = 200 GPa. Identical loads P act both vertically and horizontally at joint C, as shown. (a) If P=475 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load value Pmax if the displacement of joint B is limited to 1.5 mm? P A 45° 45° B L (a)
#4 correct units pls
TEXT:A planar construction is composed of two beam elements and two axial rods. These arejoined with frictionless joints, as indicated on the sketch. The structure is applied an outer concentrated load P=8kN in node G and a downwardevenly distributed load q=4kN/m between junctions A and D. The beam ABCD and EFG are torque rigid,while the axial rods BF and CF only absorb forces in the direction of the rods. A) Calculate the rod forces and for the external given load effect.B) Calculate the bearing reactions for the external given load effect.
Calculate all the member forces in the given truss using method of consistent deformation. Joint D is pinned supported and joint E is roller supported. F=4450 kN and L=8m. Take 'EA' same for all members В F 1 2 L 3 5 4 E
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. 6.8 m 41° Answers: AB= AD= BC= BD = CD= i i i 6.4 m 6.4 m 6.8 m, B 6080 N Z Z N N N N N
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. One load of P = 1700 Įb is applied to the assembly at A, two loads of Q = 500 lb are applied at B, and two loads of R = 1100 Ib are applied at C. The diameters of rods (1), (2), and (3) are di = 0.675 in., d2 = 0.54 in., and da = 0.945 in. Determine the axial normal stress in rod (2) (1) (3) FR A B C D
Question Three The three-bar truss ABC shown in the figure part a has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm² and modulus of elasticity E = 200 GPa. Identical loads P act both vertically and horizontally at joint C, as shown. (a) If P=475 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load value Pmax if the displacement of joint B is limited to 1.5 mm? P P A 45° 45° B woobute L (a)
Please answer carefully, do not copy. It's all wrong online.
Current Attempt in Progress Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. A 66 49° 12° W Answers: AB = i W AC = i W BC = i W