L y

Q: Which of the following most nearly gives the internal degree of indeterminacy? 102 34 28 84 Next ▸ ◄…

A: Is question is from structural analysis in this question a frame given and we are asked to find out…

Q: 4m 2m 2 m 4m 2 m

A: Find centroid of given section

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: What the center of gravity

A:

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Determine the flow in each pipeline shown if f = 0.02 for all cases. [Ans. Q, = 0.153 m³/s, Q, =…

A: Consider the free body diagram; Expression of Bernoulli's equation to C and D;…

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: discussfineness modulus

A:

Q: A frame ABCDE is subjected to forces Po, Pe, and a moment Mcas shown in the Figure below. If Po = 10…

A:

Q: 0 mm 20 mm x= ky? 30 mm etermine: enter of Area in x direction, overline x 1U-Sclect) mm enter of…

A: To find centroid

Q: Q3. Determine the plastic moment Mp of the cross sections shown, assuming the material to be…

A:

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: find the x bar at the location of centroid along y axis

A: To find x bar

Q: Weir formulas in a.) SI UNITS b.) ENGLISH UNITS

A:

Q: order (D^2+4)y

A: Given:- (D^2+4)y=sin x To find:- reduction of order

Q: (1) a L₁ B P b C L2 C D

A:

Q: Recall we applied the trapezoidal rule to determine the area of the shape given.

A: Solution;

Q: х —у (10) lim (x ,y)>(2,2) x * - y * 4

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: Mark the correct definition - Measurement is a process of determining the value or the magnitude of…

A: Measurement is the process of measuring any value with respect to the standard value. This process…

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: Consider the diagram as shown below. Now. And,

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: Find the solution of the differential equation = A. y = x B. y=x-x* C. y = √x-x4 D. y=x-1 E. Not in…

A: The given differential equation, dydx=2y4+x4xy3 To find the solution of differential equation.

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: for a simple circular curve if

A:

Q: Double integration method Find reaction A, B, and C

A:

Q: Which among the following determines the direction of closing error? a. Tan δ = ΣD/Σ O_b. c. d. Tan…

A:

Q: Determine the degree of indeterminacy for each of the following structures:

A:

Q: Assessment 1. Using your knowledge in geometry and the second direction of making lines (Direction…

A: Assessment : 1 Using your knowledge in geometry and the second direction of making lines (Direction…

Q: Determine external as well as internal indeterminacy

A: Given data : Number of member (m)=15Number of Joint (J)=10Number of external support reaction…

Q: lim of cos(29x)/29x as x approaches to infinity

A: Given Limit is approaching to infinity

Field applications of hydraulic conductivity

Hydraulic conductivity is one of the hydraulic properties of soil defined as a measurement of the ability of a porous medium to permit water movement or fluid flow through it. It is denoted by the letter K. It is influenced by the density and viscosity of the fluid. It is also called permeability. Hydraulic conductivity is defined as the ratio of velocity to the hydraulic gradient. The different methods used to determine the hydraulic conductivity are laboratory methods (constant head permeability tests and falling head tests), in-situ field methods (pumping in and pumping out tests), small scale field tests (infiltration tests and slug tests), and indirect methods such as estimation from grain size, consolidation test data, and horizontal capillary test. The pedotransfer function (PTF) method is a specific empirical estimating approach employed in the soil sciences is also used to determine the hydraulic conductivity of the soil.