The assembly consists of a steel rod CB and an aluminum rod BA, each having a diameter of 15 mm. The rod is subjected to the axial loadings at A and at the coupling B. If after applying the load coupling B displaced 1.1 mm to the right, determine the change in the dimension of the cross section of steel rod CB. The unstretched length of each segment is shown in the figure. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa Vst = 0.32

The assembly consists of a steel rod CB and an aluminum rod BA, each having a diameter of 15 mm. The rod is subjected to the axial loadings at A and at the coupling B. If after applying the load coupling B displaced 1.1 mm to the right, determine the change in the dimension of the cross section of steel rod CB. The unstretched length of each segment is shown in the figure. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa Vst = 0.32

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The strut is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of…

Q: The pin is used to connect the three links together. Due to wear, the load is distributed over the…

A: Draw the diagram. Write the expression of weight distribution on the system. Similarly, find the…

Q: The rod has a circular cross-section with a moment of inertia I. If a vertical force P is applied at…

A: Given data: The moment of inertia of the rod is I. The modulus of elasticity of the rod is E.…

Q: Both portions of the rod ABC are made of aluminum for which E = 70 GPa. Determine the deformation…

Q: The L-shaped frame is made from two segments, each of length L and flexural stiffness EI. If it is…

A: The moment due to distributed load about the point B is The vertical displacement of the point B is…

Q: A steel bar 300 mm long, 50 mm wide and 40 mm thick is subjected to a pull of 300 kN in the…

Q: 2-1. The steel framework is used to support the reinforced stone concrete slab that is used for an…

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

A: Given data: Width of the block = 20 mm Modulus of rigidity of the block, G = 26 GPa

Q: *1-28 The brace and drill bit is used to drill a hole at O. If the drill bit jams when the brace is…

Q: 1-5. Determine the resultant internal loadings acting the cross section at point B. 60 lb/ft

Q: 1-7. The cable will fail when subjected to a tension of 800ON Determine the largest vertical load P…

Q: Determine the resultant internal loadings acting on the cross section at B for the piping system…

Q: Railroad ties must be designed to resist large shear loadings. If the tie is subjected to the 34-kip…

A: Write the equation for total force acting on the tie due to the uniformly distributed reaction.…

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

Q: The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an…

Q: Determine the magnitude of the force (in N) of the x-component of the internal pin at B.

Q: 250 mm D 750 mm 120 N•m The two shafts are made of A-36 steel. Each has a diameter of 25 mm, and…

Q: The boom DF of the jib crane and the column DE have a uniform weight of 50 lb>ft. If the…

Q: The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine the…

A: Given data: The load acting at D point is PD = 800 lb The load acting at A point is PA = 400 lb The…

Q: The 20-mm-diameter A-36 steel rod is subjected to the axial forces shown. Determine the displacement…

Q: The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm2.…

A: There will be only vertical reaction at 'C' because it is a roller support and can allow horizontal…

Q: Determine the relative displacement of one end of the tapered plate with respect to the other end…

A: considering free body diagram of the system calculating width…

Q: Question 2: The load binder is used to support a load. An external moment, MA is applied to the…

Q: The polyvinyl chloride bar is subjected to an axial force of 900 lb. If it has the original…

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

Q: THE ALUMINUM MACHINE PART IS SUBJECTED TO A MOMENT M = 75 NM. DETERMINE THE MAXIMUM %3D TENSILE AND…

A: Given M=75n.M To find maximum Tensile ? and bending force ?

Q: 1-27. The pipe has a mass of 12 kg/m. If it is fixed to the wall at A, determine the resultant…

Q: P1-4. Determine the internal normal force at section A if the rod is subjected to the external…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The assembly consists of a steel rod CB and an aluminum rod BA, each having a
diameter of 15 mm. The rod is subjected to the axial loadings at A and at the
coupling B. If after applying the load coupling B displaced 1.1 mm to the right,
determine the change in the dimension of the cross section of steel rod CB. The
unstretched length of each segment is shown in the figure. Neglect the size of the
connections at B and C, and assume that they are rigid.
Est = 200 GPa Vst = 0.32
%3D
В
A
20 kN
7 kN
3 m
- 2 m·

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If P = 4.1 kN , determine the horizontal displacement of end F of rod EF.
how to do
1-105. The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is (o,)allow = 150 MPa and the allowable bearing stress for the wood is (o,)allow= 28 MPa. Assume that the hole in the washers has the same diameter as the bolt. 2 kN 3 kN 1.5 kN -2 m -2 m +1.5 m--1.5 m+1.5 m--1.5 m- ID B Prob. 1-105
*1-12. The serving tray T used on an airplane is supported on each side by an arm. The tray is pin connected to the arm at A, and at B there is a smooth pin. (The pin can move within the slot in the arms to permit folding the tray against the front passenger seat when not in use.) Determine the resultant internal loadings acting on the cross section of the arm through point C when the tray arm supports the loads shown. 12 N 9N |-100 mm- A 15 mm -150 mm В 60° T 500 mm Vc Mc
Determine the resultant internal loadings acting at the circular cross- section passing by points A and B as shown in the figure below. The correct answers should be given according to the positive sign convention. y 0.51 B
1
If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of P. The wire is A-36 steel and has a diameter of 3 mm.
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is sallow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stressconcentration at the notch.
The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stress between the pin and the bar is (0,)allow = 30ksi , determine the dimension w and t so that the gross area of the cross section is wt = 2in² and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the prjjected area whenj calculating the bearing stress.) t d w/2 w/2
1-103. The bar is supported by the pin. If the allowable tensile stress for the bar is (o)allow = 150 MPa, and the allowable shear stress for the pin is Tallow = 85 MPa, determine the diameter of the pin for which the load P will be a maximum. What is this maximum load? Assume the hole in the bar has the same diameter d as the pin. Take 1 = 6 mm and w = 50 mm.
Determine the x-y and n-t components of the 13.0 kip force F acting on the simply supported beam. Assume a = 30 ft, b = 13 ft, 0 = 12°, and = 40° A 0 a Answers: C F b B n kips Fx = kips Fy= Fn = F₁ = Hi kips kips
The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its length and its new cross-sectional dimensions at section a–a. Est = 200 GPa, nst = 0.29.