Both portions of the rod ABC are made of aluminum for which E = 70 GPa.  Determine the deformation at segment AB in millimeters if P = 42 kN and Q = 0.

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: ∑Mx=0Ta+Tc-3X5=0                           (1) COMPATABILITY,…

Q: Horizontal plates are connected to the bar AB whose length varies linearly from zero to HA, as…

A:

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

A:

Q: Both portions of the rod ABC are made of an aluminum for which E = 70 GPa.  What is the…

A:

Q: Solve Problem for the maximum shear stress within regions AC and BC, and the angle of twist f of end…

A: Considering Section AC, Maximum Shear Stress: Considering Section BC, Maximum Shear Stress:

Q: Let's consider a rod subjected to the shown axial forces. If we consider a linear elastic behavior,…

A:

Q: The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth…

A: Answer: The downward force P is 1212.85 N.

Q: The lap joint is fastened with four 3/4-inch diameter rivets. ➤a. If the allowable shearing stress…

A:

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…

A: GivenP=58kNw=14 kN/mL=3mAy=45.67 kNDy=54.33 kN

Q: The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force…

A:

Q: A solid aluminum shaft of 94 mm diameter fits concentrically in a hollow steel tube. Determine the…

A:

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A: Given data: F1=120 kNF2=90 kN Need to determine the absolute value of the deformation at point C.

Q: 4) The bar shown has a cross-sectional are of A and a modulus of elasticity of E. If the axial force…

A:

Q: Determine the magnitude of the force (in N) of the x-component of the internal pin at E.

A:

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free…

A:

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: Given data as per the question Applied load =370 KN Average shear stress =200Mpa

Q: The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be…

A: Given Data: Diameter of rivet, d=3/4 inch Working shear stress, 14000 psi Working bearing stress,…

Q: The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear…

A: Given:number of bolts, n=5Applied force, P=214 KNAverage shear stress, σ=249 MPa

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: given: P = 5 kip

Q: Two aluminum rods AB and BC hinged to rigid supports, are pinned together at B to carry a vertical…

A: Given data as per the question P =3000 lb cross-section area =0.5 in2 E=10×106 psi Calculations…

Q: Determine the total elongation or deformation in the steel bar. Given: P1= 5kN P2=27kN P3=32kN P3 A…

A:

Q: Determine the maximum value of the force P (kN) that can be applied to member AD if the allowable…

A: Given ThatA=270mm2△Lmax=3mmL1=3.8m                 L2=2.2mL3=0.85m               E=100GPa

Q: is apple showr on member ABC that is held by the 15-mm diameter cable. The pin at the support C is…

A:

Q: The lap joint is fastened with four ¾-inch diameter rivets.  a. If the allowable shearing stress of…

A:

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-16 aluminum. If a couple forces P =…

A: As applied force is at some distance from the longitudinal axis. so it generates torque and the…

Q: Determine the cross-sectional area of the shaft. Answer: A = 1 mm²

A: Given that :Vertical shaft diameter, d=20 mmthickness of plate,  t=21 mmCollar thicknesses,…

Q: 250 mm D 750 mm 120 N•m The two shafts are made of A-36 steel. Each has a diameter of 25 mm, and…

A:

Q: is it okay to solve this even if it is not in equilibrium? Why?

A: Solution:

Q: The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the…

A:

Q: The beam shown below is suspended from two steel rods as shown and is initially horizontal. The…

A: First let us find the forces acting on rod AD(FAD) and CE(FCE), Due to symmetry , FAD = Q/2 and FCE…

Q: The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter…

A: Given data The diameter of red brass copper rod AB and CD, dbr = 10 mm. The diameter of stainless…

Q: 3.23. Find dimension z so that the total stress in rod BD in Fig. 3-20 will be not more than 18,000…

A:

Q: Rigid triangle ABC is pinned at B and supported by a steel-reinforced aluminum shaft at A and an…

A: Given Rigid triangle ABC is pinned at B and supported by a steel-reinforced aluminum shaft at A and…

Q: For the stepped bar, determine the maximum bending stress (in MPa). Express your response using…

A:

Q: 20 mm. 20 mm 4. The simply supported beam on the right is built up from three boards by nailing them…

A: Given data  Load = 12 kN  Force resisted by the nails = 1.5 kN  Find the maximum allowable spacing…

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

A:

Q: Determine the average shear stress in the tube if the dimension a = 200 mm

A:

Q: A steel rod having a length of 1 m. has a cross sectional area of 100 mm2. It is subjected to an…

A: The length of the rod, L=1mThe cross-sectional area of the rod, A= 100 mm2The applied tensile load,…

Q: 04. The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a pin.…

A: Draw the free body diagram at point .

Q: Rod BD is made of steel (E= 29 × 100 psi) and is used to brace the axially compressed member ABC.…

A:

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.