900 lb 900 lb 3 in. 6 in. 1 in.

Q: The strut is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of…

A:

Q: A steel bar 300 mm long, 50 mm wide and 40 mm thick is subjected to a pull of 300 kN  in the…

A:

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

A: Given data: Width of the block = 20 mm Modulus of rigidity of the block, G = 26 GPa

Q: The rigid bar ABC and EFG are supported by pins at A and G. The vertical rods are made of steel (rod…

A: Given: The temperature change, Δt = 50o The coefficient of thermal expansion, α = 0.0000117/oC The…

Q: The wires AB and AC are made of steel, and wire AD is made of copper. Before the 150-lb force is…

A: By using the equations of equilibrium ;ΣFx=0 ⇒FAC cos 45°-FAB cos 45°=0FAC=FAB=F-1ΣFy=0⇒FAC…

Q: If the allowable tensile stress for wires AB and AC is sallow = 180 MPa, and wire AB has a diameter…

A:

Q: A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v =…

A:

Q: An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top…

A: Given Data: The horizontal force P = 2 kN. The displacement of the top plate is d = 2 mm. The…

Q: The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an…

A:

Q: The wires AB and AC are made of steel, and wire AD is made of aluminum. Before the 300 kN force is…

A:

Q: The bar is connected to the support using a pin having a diameter of d = 1 in. If the allowable…

A:

Q: The force P is applied to the bar, which is made from an elastic perfectly plastic material.…

A: Given, Section 1 = AB Length of AB (L1) = 6 in Cross section Area of AB (A1) = 1 in2 Load in AB = P1…

Q: A bar having a length of 5 in. and a cross-sectional area of 0.7 in.2 is subjected to an axial force…

A: Here modulus of elasticity is given by E=σεWhere σ=Tensile Stressε=Tensile strainSo now tensile…

Q: 1. The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is…

A: Given data: The length of the rod, L = 200 mm. The diameter of the rod, d = 15 mm. The young’s…

Q: If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of P.…

A: Given Data: The length of wire is l = 300 mm. The diameter of wire is d = 3 mm. The elongation in…

Q: *3-28. The elastic portion of the stress-strain diagram for a steel alloy is shown in the figure.…

A: Up to proportional limit we can use the Generalized Hooke's Law.

Q: The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load…

A:

Q: The pole is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of 0.2…

A: For A-36 steel  Youngs Modulus, E = 29 x 103 ksi yield strength, = 36 ksi…

Q: A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN.…

A:

Q: The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an…

A: Given data: Diameter of the bolt (db) = 10 mm Inner diameter of the sleeve (dsi) = 15 mm Outer…

Q: Problem #3: Determine the shear strain yry at corners A and B if the plastic distorts as shown by…

A:

Q: The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: The A-36 steel bar consists of two segments, one of a circular cross-section of radius r, and one of…

A: The expression for the strain energy in the square segment is given as, Us=P2L2AE Here, P is the…

Q: The plastic 50-mm diameter rod is placed in a 51-mm-diameter hole with rigid walls. Determine the…

A: Given:Rod diameter, d = 50 mmHole diameter, dh = 51 mmLoad, P = 8 kN or 8000 NE = 40 MPav =…

Q: The rod has a circular cross section. If it is made of an elastic perfectly plastic material,…

A: Draw the cross section of the rod showing half-section in tension and half-section in compression.

Q: The rod is subjected to an external axial force of 800 N and a uniform distributed load of 100…

A: givenexternal axial force Fa=800Nuniform distributed load w= 100 N/mlength of cantilever beam L=2m

Q: 3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections…

A: Given data:- Rigidly connected rods To find out:- force stress in AB stress in BC

Q: 300 N 200 mm 300 N

A:

Q: The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2.…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.