The application rate of a certain chemical is recommended at 4 kg/ha. The calibration test of a 16-liter knapsack sprayer is as follows: Nozzle discharge = 1.2 liters/min, swath = 1.5 m and walking speed = 20 m/min Determine the total volume of water applied per hectare: a. 200 liters b. 300 liters c. 400 liters d. 500 liters

Q: 1) Pitot tube can be used to measure the flow velocity. The equation can be derived from Bernoulli…

A:

Q: From the below given graph for venturimeter experiment the value of A is 5.05 and the value of B is…

A:

Q: 3 Density of a brine is 1035 kg/m, mass flow rate is 776.25 kg/s, then the volume flow rate is…

A: We have to determine volume flow rate

Q: Question 2 Answer the following question and give justifications: a) Hassan is assigned to purchase…

A: As per honor code and answering guidelines I can answer 1st question at a time.If you want other…

Q: A Newtonian fluid having a viscosity of 0.38 N. s/m2 and a specific gravity of 0.91 flows through a…

A:

Q: Select the right answer from the following and put the correct choice in the answer table below…

A:

Q: What is the pressure at the exit of the pipe

A: a.100kPa

Q: Show the complete and legible solutions, with the format - GIVEN, REQUIRED, SOLUTION, FINAL, and…

A:

Q: You have an orifice meter that was calibrated for air at 70oF and I atm, You are using it to measure…

A: Given, calibrated conditions-                Tc = 70 * F = 294.26 K                 Pc = 1 atm…

Q: A certain centrifugal pump was tested and its performance curves can be approximated as follows: H =…

A:

Q: The more accurate flow measuring instrument is * Flowmeter Venturimeter Rotameter Orificemeter Q2.…

A:

Q: Calculate the dynamic viscosity of an oil, which is used for lubrication between square plate of…

A: Write the given data with suitable variables. A=700 mm×700 mm=0.7 m×0.7 m1000 mm1 mθ=45°W=250…

Q: At cross-section 1 the average velocity of the water in the pipe is 0.922 m/s and the pressure is…

A: Let Q=Volumetric flow rate =4.69m3/s v3=Velocity at section 3 = (3X1.29)/4 =0.96m/s v4=Velocity at…

Q: Water flows vertically inside the pipe, a manometer with a specific gravity of S=0.6 used to measure…

A: Given      Specific gravity = 0.6 Therefore                   Density = 600 kg / m3

Q: A Pitot tube is going to be used with an airflow at 32°C and 5 atm, and a velocity is 3 m/s: a)…

A: Given data: The density of air at 32 degrees Celsius can be determined from the ideal gas equation…

Q: A tank shown has two fluids water and gasoline (S.G-0.75), the local atmospheric pressure is 101 kPa…

A:

Q: Q) Air conditioning system supplies two rooms required deferent conditions. Room 1 is to be minted…

A:

Q: For a fluid flow at a particular point, the flow parameters found to be not varying with time. The…

A: Steady Flow  is the flow for which the flow parameter does not change with time. Hence, correct…

Q: A wind tunnel has an inlet section with a velocity of 360 ft/s at standard atmospheric conditions.…

A: Velocity at inlet, V1= 360 ft/s= 360(0.3048) m/s= 109.728 m/s Pressure at inlet, P1= Patm= 101325…

Q: Please  provide complete solution and diagram. An air compressor takes air and discharges it to 200…

A:

Q: The base result which error is calculated with reference to in measuring water flow Select one: a.…

A: VOLUMETRIC BENCH  is used find the error from the measuring water flow.

Q: A tank shown has two fluids water and gasoline (S.G=0.85), the local atmospheric pressure is 101…

A: Given data :-  Specific gravity of gasoline = 0.85           so, the density of the gasoline, = 0.85…

Q: 8:02 LTE1.ll 2% Assignment Details Fluid Mechanics - Alejandro R. MANDERICO Oil S = 0.842 Water ha…

A:

Q: A 140 m long pipeline runs between two reservoirs, both ends being under water, and the intake end…

A: Given:Length of the pipe, L=140 mDifference between the water levels in the two reservoirs, H=40 ma…

Q: 26. Inlet and throat diameters of a horizontal venturimeter are 270 mm and 130 mm respectively. The…

A:

Q: Dusty air at a fertilizer plant flows through a 13% efficient cyclone and then through an ESP, The…

A: The allowable concentration of dust in the air that exists from the ESP Callow=1.5/100(80)=1.2…

Q: Topic : Mixture Flow Problem A tank initially holds 100 gal of salt solution in which 50 Ib of salt…

A: Please find the answer below

Q: A dilute sugar-water solution enters a pipe with an ID of 3.05 inches at rate of 15.6 ft^3/hr, then…

A: Givendi=3.05in=0.254ftdo=6.4in=0.533ftQ=15.6 ft3/hr

Q: A fluid (SG = 1.3) flows from a nozzle. The nozzle is 15m above the datum. The power on the nozzle…

A:

Q: Reynolds number is the ratio of inertial force to:

A: Reynold's Number: It is defined as the ratio of inertia force of a flowing fluid and the viscous…

Q: Water flows through a pipe of varying cross-section and varying elevation at the rate of 22.2m3/min.…

A: Given:Q=22.2 m3/min =0.37 m3/sz1=3 mr1=0.36 mP1=12 N/cm2 =0.012 MPa      =12 KPar2=18 cmz2= 0.7 m

Q: 1. ketch a diagram for the and any and de 2. State any possible error source in the estimation of K…

A:

Q: 16 - Which is used to measure the internal resistance of fluids to flow?    A) Saybolt Viscometer…

A: To find: Which is used to measure the internal resistance of fluids to flow?

Q: 21. The following are the results of tests conducted on a centrifugal pump. Negative pressure head…

A: Given: The negative pressure head in the suction pipe, hs = -22 cm of mercury The pressure head in…

Q: CS) Flow through a heat exchanger tube is to be studied by means of a 1/10 scale model. If the…

A:

Q: Given: A pipe connecting two reservoirs as shown in Fig. 1. Absolute roughness of both pipe sections…

A: INTRODUCTION : When the fluid flow through the pipe or section, the fluid always experiences losses…

Q: Convert the values provided below in terms of specified units.

A: Given

Q: Maximizing the wind velocity of 92 m/s and 25 units of wind turbine was installed at the seaside…

A: ◆ The total power produced by the wind turbine power plant is 49.23 MW. ◆ Hence, option D is…

Q: Fluid flowing at 13 gpm experiences a 140 psi pressure drop as is passes through a DCV. The fluid…

A: Q˙=13 gpm=0.02896412 ft3/sP=140 psi =140×144 psf=20160 psfSG=0.88 C=0.45 Btu/(lboF)

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.