Fluid flowing at 13 gpm experiences a 140 psi pressure drop as is passes through a DCV. The fluid has a specific gravity of 0.88 and a specific heat of 0.45 Btu/(lb °F). Find temperature rise in the fluid as it passes through the valve.

Q: 2 Pressure gauge √x the hydraulic cycle in figure -consist of:7 5 6 X 3 Feed direction tank O…

A: ◆ Figure represented by no. 7 is tank. ◆ Therefore, correct option is (a).

Q: The figure below shows a schematic representation of compressor characteristics. What is the name…

A: Surge line is the name usually given to the uppermost line that contains point d only.

Q: A pitot-static probe, as depicted in Figure below, can be used to detect the velocity of a flowing…

A: Velocity is a physical vector quantity that requires both magnitude and direction to be defined.…

Q: Describe how the system works

A: A hydraulic system is a drive technique in which energy is transferred from an electric motor to…

Q: RPM meter of the car is an example for control of process application of measurement system. Select…

A: A tachometer or RPM meter is an instrument measuring the rotation speed of a shaft or disk, as in a…

Q: Consider a two-stage cascade refrigeration system operating between the pressure limits of 1.2 MPa…

A: Solution to A and B as mentioned by the student:

Q: Based on the circuit shown in Figure 19-11, complete the following exercises: A. Complete the chart…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: How long does the engineer need to wait at least to see the 95 C?

A:

Q: 5-What does do the exciter system in turbo generator unit? Sketch a block diagram of a typical…

A:

Q: 9mm Ġ Diameter 5mm x 10 150mm (Aluminium 6060) An aluminium block with holes drilled through all…

A: Write the given data with suitable variables. L=300 mB=150 mm=0.15 mH=9 mm=0.009 md=5 mm=0.005…

Q: In the following application, a temperature switch controls a heating contactor and a flow switch is…

A: Signal devices in the circuit: Cold air.    Supply air.  Heating contractor.  Alarm.  On delay…

Q: Draw a Process and Instrumentation Diagrams (P&ID) for the above distillation column. Draw the…

A: T1 = temperature indicatorp1 = pressure indicatorTE = Temperature elementTT = Temperature…

Q: Problem Description Components are to be continuously stamped with a stamping device. After the…

A: Given : To find : Pneumatic and Electric circuit diagram

Q: Match the following terms with the definitions. Damping Bandwidth End point Home position…

A: Solution:   The following are correctly matched below:

Q: Choose the symbol for Fixed displacement single rotation compressor. Select one: Oa. O b Od.

A: Answer fixed-displacement pump may be a positive relocation sort where the sum of uprooting (gpm)…

Q: Does the velocity change across a stator?

A: Yes, the velocity change across a stator.

Q: The throttle opening is electronically controlled; the position When the throttle is fully open,…

A: Given Engine setup To find Role of Air filter Air temperature sensor Intake manifold (tumbler) valve…

Q: Symbols Questions 1) Give the name of the following graphic symbols. P1 А В P T

A:

Q: Q5: The chosen of the type and applications of chiller depend on

A: Solution:

Q: Draw the graphic symbol for a two-position spring centered valve, a spring offset valve, an…

A: Valve symbols are used to develop hydraulic circuits with ease. They convey the necessary…

Q: If you have a velocity triangle for a rotor, what is the stator blade angle?

A: To explain: If you have a velocity triangle for a rotor, what is the stator blade angle?

Q: initially at 2.75°C with a qualit 0.2. The pressure is held cons nitrogen gas acting against a…

A: Given Data The mass of the R134a is:m1=15 kg The initial temperature is:T1=2.75°C The quality…

Q: Different types of IC engines

A: Given:

Q: Explain the function of the fan in making the vacuum cleaner work.

A: Low air pressure is used by vacuum cleaners to assist us pick up minute particles of dirt and…

Q: Q6 Hydraulle cylinder Rocking lever Pressure valve Oper element Direction- control valve -Throttle…

A: Extension side: Consider only the piston area.Retraction: Calculate piston area minus rod area.This…

Q: Circuit Problem and Description: Using the given components, design a pneumatic circuit which will…

A: Given : Circuit description To find : Circuit diagram

Q: of vibration The number of cycles per unit time is called the Select one: O a. period O b. amplitude…

A: The number of cycles per unit time is called

Q: All manipulators don't have workspace-boundary singularities. O True O False

A: Boundary Singularities (too known as workspace singularities) are a common sort of peculiarity.…

Q: Give one example of an engine management system fault for each component Air-flow meters…

A: An Air flow meter monitors the air entering into the engine mostly in automotive engines so that…

Q: Consider a two-stage cascade refrigeration system operating between the pressure limits of 1.2 MPa…

A:

Q: What does it mean to shift the patient into the treatment position? Could you describe the…

A: Shifting of any patient from stretcher or bed to the treatment position consist of the transfer of…

Q: Draw and label the parts of the following: 1. Central AC Compressor 2. Window air conditioning…

A: 1: The main parts used in central AC compressors are, Check valve Pump Pump flywheel Air filter…

Q: otto cycle p-v and t-s diagram explication.

A: The objective of the question is to explain the Pressure-Volume (P-V) and Temperature-Entropy (T-S)…

Q: A thermostat adjusting mechanism capillary tube sensing bulb A 3D printer head moving mechanism…

A: The thermostat adjusting mechanism can be categorized as a function generation case. In this…

Q: Define the term in theory of macines Meyer's expansion valve

A: The Meyer's expansion valve consists of two valve known as  main valve and expansion valve which are…

Q: please show the derivation for this plroblem

A:

Q: It is desired to operate the pneumatic cylinder below which has to pistons A and B to stamp the die…

A:

Q: the engine rpm is measured by measuring the current of an alternrator, driven by the engine…

A: the engine rpm is measured by measuring the frequency of an alternrator, driven by the engine

Q: Which of the following is an example of fluid statics Water fall Water moving through a pipeline…

A: Fluid statics is the topic of fluid mechanics in which we study about the fluid at rest.

Q: Answers by (True or False) 1. The primary variable is T1, the temperature inside the tank. 2. The…

A: True True True

Q: 2. (a) What is the temperature of air molecules if their average kinetic energy is 61 meV? (b) A…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.