The amplitude spectrum of a CT signal is given by the function If|< 100 \f|> 100 X(f) = 100 - |F| i. Draw the spectrum of CT signal. What is the standard name for the shape of the spectrum drawn? ii. Draw the spectrum of the sampled signal assuming that signal is over sampled by 30% iii. Determine the sampling frequency to produce 100 Hz separation between repetitive copies.

The amplitude spectrum of a CT signal is given by the function If|< 100 \f|> 100 X(f) = 100 - |F| i. Draw the spectrum of CT signal. What is the standard name for the shape of the spectrum drawn? ii. Draw the spectrum of the sampled signal assuming that signal is over sampled by 30% iii. Determine the sampling frequency to produce 100 Hz separation between repetitive copies.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
This configuration can overcome the disturbances. Close-loop System Open-loop System Closed-loop System Opened-loop System
duration? Q8. What is the difference between Zener breakdown and Avalanche breakdown?
Topic : Analogous Circuits for Direct Radiator Loudspeaker Please answer #4 and #5 ONLY!
3 - Which of the following is true about the LEAD compensator?A) It decreases the rise time.B) It decreases the number of branches of the root-locus curve.C) NoneD) Increases the number of branches of the root-locus curve.E) It reduces the steady state error and increases the stability.
H.W-I:- A platinum Coil has a resistance of 3.146 N at (40°c) and 3.7670 at (100°c). Find the resistance at (0°c) and temperature cocfficient of resistance at (40°c).
g- Continuous current operation in step-down chopper is gained when.............. 1- txT, 3-1,4-¹, 5- None of j- The time available to turn-off thyristor in load-commutated chopper is 3- 2E²Cf, 4-E²Cf, 5- None of previous. lo Io 1-√ √LC, 2-2√ √LC, 3-0.5√ √LmC, 1-2, 2-EC
Quiq plz
B-Two practical coils with internal resistances of R1, R2 has quality factors of Q1& Q2 respectively. If these two coils are connected in series find the resultant quality factor. ... ..
Describe real and reactive power regulation
In the Transmission Line Simulator, the Transmission Line is composed of which parameter/s? O A. The Shunt Conductance Only O B. The Series Impedance and Shunt Capacitance O C. The Shunt Capacitance Only O D. The Series Impedance Only