Question 1: The measured output voltage of a cable is 7mv, for an input voltage of 15mv andthe near end cross talk ratio (NEXT) of the cable is 20dB. Find attenuation and attenuation tocross talk ratio (ACR) of the cable.Question 2:2.1. A piece of a coaxial cable has a 85 ohm characteristic impedance and a nominalcapacitance is 35pF/m. what is its inductance per meter? If the diameter of the innerconductor is 0.385mm, then what is the diameter of the outer conductor?2.2. A transmission line has inductance of 0.1 milli henry and capacitance of 1 microfarad. The line is a lossless line. Find its characteristic impedance.1Question 3: Enumerate solutions to decrease propagation delay.Question 4: What are the effects of delay skew on the signal?Question 5: List the capacitance values of all types of UTP, STP and COAXIAL CABLES.

We are authorized to answer one question at a time, since you have not mentioned which question you…

Question 1: The measured output voltage of a cable is 7mv, for an input voltage of 15mv and the near end cross talk ratio (NEXT) of the cable is 20dB. Find attenuation and attenuation to cross talk ratio (ACR) of the cable.

Question 1: The measured output voltage of a cable is 7mv, for an input voltage of 15mv and the near end cross talk ratio (NEXT) of the cable is 20dB. Find attenuation and attenuation to cross talk ratio (ACR) of the cable.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the diagram of a halfwave power supply circuit and a fullwave supply circuit. Aside from the difference between the number of diode utilized in both circuits, state the main advantage of the fullwave power against the halfwave circuit for the following scenario . When there is a defective diode (open anode- cathode ) When the filter capacitor is defective (capacitor is open)
In an Amplitude Modulator where the carrier and modulating signals are both sine waves, the frequency spectrum of the resulting AM signal is shown below. 10V 2V 2V kHz 803 808.6 a) Determine the equation of the modulating signal b) Calculate the bandwidth of the AM signal c) Calculate the effective current of the AM signal thru a 75-ohm load. d) Sketch the AM wave and label the maximum and minimum voltage of the signal.
Derive the frequency reuse factor for a triangular cell
How the phase modulation can generate frequency modulation?
Modify this circuit to extend the upper frequency limit to greater than 15 MHz. You may change the topology (i.e. configuration), but not the power supply voltage or collector bias current. The circuit voltage gain must be 46dB +/- 1 dB. Provide simulation results to show AC frequency responses of both circuits on the same plot, and annotate the 3dB upper frequency limit on both traces. Use typical ẞ values from the data sheet for the simulation. You may assume that 1% resistors are available in values below 100. The circuit must adhere to Standard Bias techniques. V4 Rser=0 SINE(0 0.02 10k) AC 1 VCC ୯ V2 +15V Cin1 1μ -VCC VCC R4 Rc1 147k 7k Q3 2N3904 R7 R6 9.09 20.5k Ce1 Re1 1.00k 10p Out
None
9. For a two-tone test signal of 3 kHz and 4 kHz and a carrier frequency of 400 kHz, determine output frequency spectrum. Also, given that E, and E2 = 20 Vp and a load resistor of 100 ohms, determine the PEP and average power.
2. The output impedance of 600 ohms radio transmitter with signal strength reading on a meter of impedance 75ohms by 0.81 neper of unbalance non-symmetrical Pi-pad attenuator circuit. Determine the required resistor values to design this attenuator.
Figure (1) shows the block diagram of a wideband frequency modulator using the indirect method. This modulator is used to transmit audio signals containing frequencies in the range of 100 Hz to 15 kHz. The narrowband is supplied with a carrier of frequency fl-0.1 MHz by crystal- controlled oscillator also ß-0.2, a second crystal- controlled oscillator supplied a sinusoidal wave of frequency 9.5 MHz to the mixer. The system Carrier frequency at the transmitter output, fc-100MHz Minimum frequency deviation, Af-75, find nl and n2? f(t) NBFM Freq. Multiplier 1 Oscillator1 Fig. (1) Mixer Oscillator2 Freq. Multiplier 2 frm(t) n1=72, n2=47 O n1=73, n2-48 O n1=75, n2=50 n1=77, n2=52 O n1=76, n2=51 O
4) Listen A sinewave voltage is defined by an effective voltage of 2.82Vrms. Calculation of the amplitude Vpk is performed: By multiplying Vrms by 2/Pi (=0.637). By dividing Vrms by 1.41 (square root of 2). By multiplying Vrms by 1.41 (square root of 2). By dividing Vrms by 2/Pi (=0.637). Calculation cannot be done since we do not know the frequency of the signal. O None of these statements are true. prt sc 144
Which of the following is true about the AC equivalent of FETS? D-MOSFET and E-MOSFET are the same while JFET is different. JFET and D-MOSFET are the same while E-MOSFET is different. O They are the same. They are entirely different.
Derive the expression for Zout