The air has a dry ball temperature of 34 °C and a wet bulb temperature of 20 °C is initially heated in a heater so that the temperature of the dry ball increases to 80 °C. Then the air is passed through the corn kernels to dry. The air that comes out of the corn kernels is at a dry bulb temperature of 55 °C. Then this air is passed to the dehumidifier to reduce the Relative humidity to 10%. Draw the course of this process of changing the air on a psychrometric diagram. The airflow rate through the corn kernels and dehumidifier was 4.0 m / s and the diameter of the pile was 0.7 m. a. Determine the amount of water lost from the pile of corn kernels (in grams of water / second) = answer (grams of water / second) b. Determine the amount of water lost from the air when passing through the dehumidifier (in grams of water / second) = answer (grams of water / second)

Q: a. Discuss the two main general principles in drying. b. The air emerging from a dryer, with an exit…

A:

Q: Now explore the influence of the mass of the block. Using the copper block and a 4.0 second flame,…

A: Given that, The initial temperature of 10 g block T1 = 20oC The final temperature of 10 g block T2 =…

Q: Paper is made from a suspension of fibers in water. The process begins by draining the fibers to a…

A: The type of dryer required to dry the paper is to be mentioned.

Q: temperature. * O True O False Nan

A: The above question is the question of the heat exchanger. There are many reasons that decrease the…

Q: Choose the correct option: 7. Which of the following metals best transfers heat? a) Gold b) Copper…

A: It is required to determine the metals that transfers the heat best.

Q: In the figure below there are two different drying kinetics curves, analyze them and answer: a)…

A:

Q: Fuel flows in to the burner and is burnt with air provided from an air blower. * true O False O Nan

A: It is to be determined whether fuel flowing into the burner is burnt with air provided from an air…

Q: 10 cm thick beef steak will be frozen in the freezer room -25 degrees Celsius. This product has a…

A:

Q: Aluminum has a specific heat of 0.897 J/g °C. How much heat is needed to raise the temperature of a…

A: Given: Specific heat = 0.897 J/g. C   Mass (m) = 79 gm Temperature: T1 = 25 C (ambient assumed), T2…

Q: 1500 lb/h of a waste mixture of 40 percent benzene, 50 percent toluene, and 10 percent water is…

A:

Q: e air has a dry ball temperature of 30 ° C and a wet bulb temperature of 22 ° C is initially heated…

A:

Q: Air at a dry ball temperature of 85° C and 5% RH is passed over the cooling coil so that the air dry…

A: Given Data: Dry bulb temperature TDB1 = 85 °C Relative Humidity RH% = 5% Dry bulb temperature TDB2 =…

Q: the amount of excess combustion air is normally determined by analysis of stack_____ a) the fuel…

A: Excess air is the air which is used in excess for combustion of various fuels (solids, liquid, and…

Q: Choose the correct option: 8. Considering the physical and chemical properties, abundance, and even…

A:

Q: The air has a dry ball temperature of 40 ° C and a wet bulb temperature of 20 ° C is initially…

A:

Q: Fermentation process can be done in a which is having stirrer and heating system.

A: the fermentation process is carried out in which system__ Select a suitable option.

Q: The air has a dry ball temperature of 34 °C and a wet bulb temperature of 20 °C is initially heated…

A: Intial DBT of air, T1=340CFinal DBT of air, T2=800CWB of air=200CDBT of corn kernals,…

Q: Calculat surrounding Calculate th covered with much heat w

A:

Q: Slab building boards contain 17% moisture by weight. They are dried to a water content of 1% by…

A: Given that, The weight% of moisture in the building boards = 17% The weight% of solids in the…

Q: In the steel industry, one of the most important processes done is known as quenching. This process…

A: Given details, Mass of steel cube,ms=7 kg initial Temperature of steel,Ts1=700 C=700+273=973 K Mass…

Q: Calculate the accentic factor of oxygen gas at 30 C and 5Mpa.

A:

Q: True or False

A: Ans 1- True  2-  False ( because cooling and chilling rate are governed by any of form it can be…

Q: Effect of the carbon percentage on the shape and magnitude (mechanical properties) of stress-strain…

A:

Q: Calculate the theoretical flame temperature, in Kelvin, when ethylene at 25C is burned with 48 %…

A: Write the reaction for the combustion of ethylene as follows: C2H4 + 3O2 → 2CO2 + 2H2O   1 mole of…

Q: 3. The specific heat of aluminium is 0.22 call/g-C°. that is the value of the specific heat in a)…

A: Consider Aluminum with its specific heat of  0.22 cal g-1°C-1.

Q: A sample has initial mass of 10 grams. The quantity of water removed in the oven is 2 grams. The…

A: The initial mass of the sample, mi = 10 g Mass of moisture removed from the sample, mM = 2 g

Q: Calculate the latent heat of condensation for water at 8 MPa. Compare with values from steam table.

A: Given data: Pressure = 8 Mpa Calculate the latent heat of condensation for water.

Q: Why is it that when a bagasse is dried at above100 degrees Celsius at the dryer chemical process…

A: It is to be stated that why all water gets removed from bagasse if it is dried above 100 degree…

Q: As as chemical engineer analyse how does the choice of humidification method, such as adiabatic or…

A: Cooling towers are essential components of many chemical process plants, used to dissipate heat from…

Q: The air conditioning process in the humidifier, air at a dry bulb temperature of 30 °C and RH of 15%…

A: Dry bulb temperature of air= 300CInitial %RH of air=15%Final %RH of air=50%

Q: Material Density Specific Latent Heat Latent Heat Thermal of Fusion, of Нeat kgK. Conductivity W…

A: Considered a heater blanket of 2000 W having a negligible thickness and the heat is the transfer…

Q: in the manufacture of pulp from the delignification process using an operating temperature of 100C.…

A: Delignification is the system of extracting lignin from plant sources, can be carried out the usage…

Q: A composite wall is formed of a 2.5-cm copper plate, a 3.2-mm layer of asbestos, and a 5-cm layer of…

A: Composite wall dimensions are as follows,Thickness of copper plate = 2.5 cm, Thickness of asbestos =…

Q: Consider a Cu-60wt% Ni-40% alloy , determine the following: (a) The liquidus and solidus temperature…

A:

Q: You have been provided with a graph labelled Graph A (See Microsoft Teams or click here) that is the…

A: a) weight of sample=200g weight percent of copper=10% temperature=932°C from the graph we can see…

Q: a) Assume that a dielectric crystal consists of atomic planes that do not interact with each other,…

A: Here two question is given. only 1st one is answered.   Debye approximation predicts the…

Q: Furnaces are used through out the industry to provide the O energy mass heat

A: A furnace (also referred to as a heater) can either be a unit used to heat an interior space through…

Q: Insulating material is used to reduce heat loss from the heating furnace walls to the room. The…

A: Write the expression for heat flux as follows: QA = -k∆T∆xQA = -kTo-TIx      .....1

Distillation

Distillation is a process/technique to separate more volatile components from less volatile components using the principle of relative volatility. In chemical engineering, distillation is one of the most common and important topics that is involved in almost every industry and process.