The 200-mm radius brake drum is attached to a larger flywheel that is not shown. The total mass moment of inertia of the drum and the flywheel is 20 kg-m² and the coefficient of kinetic friction between the drum and the brake shoe at B is 0.35. Knowing that the angular velocity of the flywheel is 360 rpm counterclockwise when a force P of magnitude 350 N is applied to the pedal C, determine the number of revolutions executed by the flywheel before it comes to rest. 150 mm 250 mm 200 mm B 375 mm

The 200-mm radius brake drum is attached to a larger flywheel that is not shown. The total mass moment of inertia of the drum and the flywheel is 20 kg-m² and the coefficient of kinetic friction between the drum and the brake shoe at B is 0.35. Knowing that the angular velocity of the flywheel is 360 rpm counterclockwise when a force P of magnitude 350 N is applied to the pedal C, determine the number of revolutions executed by the flywheel before it comes to rest. 150 mm 250 mm 200 mm B 375 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given: The gear shown moves on a fixed horizontal rack. The gear has mass m and a radius of gyration of k equal to its radius. The rod BC connected to the gear has length 1, and mass 2m with center of mass located at pt. G. The slider at B has negligible mass, and the attached spring has a spring constant k equal to mg/l. The system is released from rest in a vertical position (the bar BC is vertical). In this position, the spring is unstretched. The system has negligible friction and mass of the spring. k mrod G R mrod = 2m mgear = m l, I= mgear, k Find: Find the velocity of the point C on the gear after it has moved a distance of 1,/2 to the right.
A 3 cylinder single acting engine has its cranks set equally at 120° and it runs at 600 rpm. The Torque crank angle diagram for each cylinder is a triangle for the power with maximum torque 80 N-m at 60° after dead centre of the corresponding crank. The torque on the return stroke is sensibly zero. Determine the (a) Power developed (b) K if the flywheel used has a mass of 10 Kg. and radius of gyration is 8 cm (c) Coefficient of luctuation of energy (d) Maximum angle of the flywheel CYLI CYL2 CYL3 80 MMT 60 120 I 8O 240 300 360
3
Problem No. 5 A rotating shaft carries four masses A, B, C and D rigidly attached to it; the centers of mass are at 30 mm, 36 mm, 39 mm and 33 mm respectively from the axis of rotation. The masses are 7.5 kg, mB, 5 kg and 4 kg respectively. The axial distance between A and B is 0.4 m, that between B and C is 0.5 m and the axial distance between C and D is H meters. The eccentricities of A and C are at 90° to one another. If the shaft is to be balanced completely, find mB, H and the angular positions of the masses B and D.
A uniform 144-lb cube is attached to a uniform 136-lb circular shaft as shown, and a couple M with a constant magnitude is applied to the shaft when the system is at rest. Knowing that r = 4 in., L= 12 in., and the angular velocity of the system is 960 rpm after 4 s, determine the magnitude of the couple M.
Dynamic Problem, reply as soon as posible. The double pulley system weighs 30 lbs. and has a 6.5-inch center radius of gyration. Cylinders A and B areconnected to the double pulley by cords that wrap around the circles whose radii are shown. Thecoefficient of kinetic friction between block B and the surface is 0.25. If the system is released from rest atposition shown, determine:A) The velocity of cylinder A just before hitting the ground.B) The total distance cylinder B travels before coming to rest.
A 5.32-kg disk A of radius 0.445 m initially rotating counter-clockwise at 436 rev/min is engaged with a 6.72-kg disk B of radius 0.275 m initially rotating clockwise at 528 rev/min, where the moment of inertia of a disk is given as I = ½ mi?. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disks. Remember to show clearly the equations that you use!!'
Problem # 5) A pulley having a moment of inertia of 0.191b-ft-s² is connected to two masses as shown. The masses A and B have linear acceleration of 1.85ft/s² upward and 1.11 ft/s² downward, respectively. Assuming no axle friction, determine (a) the tension forces TA and TB in the cables connecting the masses, and (b) the angular acceleration a of the pulley. Include and present the Free Body Diagram and Inertial Response Diagram as part of the solving process. Hint #1: Hint #2: use mA = 0.1553slugs, and mв = 0.3106slugs treat each body separately 6 in. B 10 lb 10 in. A 5 lb
Please display all work
A 240-lb block is suspended from an inextensible cable which is wrapped around a drum of 1.25-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of intertia of 10.5 lb-ft-s^2. At the instant shown, the velocity of the block is 6 ft/s directed downward. The bearing at A as a frictional moment of 60 lb-ft. What is the kinetic energy of the system after the block moved after 4ft? (in ft-lb)
A 197-kg flywheel is at rest when a constant 300 N·m couple is applied. After executing 560 revolutions, the flywheel reaches its rated speed of 2400 rpm. Knowing that the radius of gyration of the flywheel is 400 mm, determine the average magnitude of the couple due to kinetic friction in the bearing. N.m. The average magnitude of the couple due to kinetic friction in the bearing is [
The rotor of an electric motor has an angular velocity of 4500 rpm when the load and power are cut off. The 75-kg rotor, which has a centroidal radius of gyration of 200 mm, then coasts to rest. Knowing that kinetic friction results in a couple of magnitude 4.5 N m⋅ exerted on the rotor, determine the number of revolutions that the rotor executes before coming to rest. (Final answers should be in two decimal places with correct units)