The rotor of an electric motor has an angular velocity of 3520 rpm when the load and power are cut off. The 110-lb rotor, which has a centroidal radius of gyration of 9 in., then coasts to rest. Knowing that the kinetic friction of the rotor produces a couple of magnitude 2.5 lb-ft, determine the number of revolutions that the rotor executes before coming to rest. The number of revolutions that the rotor executes before coming to rest is rev.

The rotor of an electric motor has an angular velocity of 3520 rpm when the load and power are cut off. The 110-lb rotor, which has a centroidal radius of gyration of 9 in., then coasts to rest. Knowing that the kinetic friction of the rotor produces a couple of magnitude 2.5 lb-ft, determine the number of revolutions that the rotor executes before coming to rest. The number of revolutions that the rotor executes before coming to rest is rev.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3
Dynamic Problem, reply as soon as posible. The double pulley system weighs 30 lbs. and has a 6.5-inch center radius of gyration. Cylinders A and B areconnected to the double pulley by cords that wrap around the circles whose radii are shown. Thecoefficient of kinetic friction between block B and the surface is 0.25. If the system is released from rest atposition shown, determine:A) The velocity of cylinder A just before hitting the ground.B) The total distance cylinder B travels before coming to rest.
A 5.32-kg disk A of radius 0.445 m initially rotating counter-clockwise at 436 rev/min is engaged with a 6.72-kg disk B of radius 0.275 m initially rotating clockwise at 528 rev/min, where the moment of inertia of a disk is given as I = ½ mi?. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disks. Remember to show clearly the equations that you use!!'
The rotor of a gas turbine is turning at a speed of 5,600 rpm when the turbine is turned off. It is observed that it takes 5 min for the rotor to come to rest. Assuming that the motion is uniformly accelerated, determine the angular acceleration of the rotor.
Solve it correctly. I ll rate
25
A 240-lb block is suspended from an inextensible cable which is wrapped around a drum of 1.25-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of intertia of 10.5 lb-ft-s^2. At the instant shown, the velocity of the block is 6 ft/s directed downward. The bearing at A as a frictional moment of 60 lb-ft. What is the kinetic energy of the system after the block moved after 4ft? (in ft-lb)
A 197-kg flywheel is at rest when a constant 300 N·m couple is applied. After executing 560 revolutions, the flywheel reaches its rated speed of 2400 rpm. Knowing that the radius of gyration of the flywheel is 400 mm, determine the average magnitude of the couple due to kinetic friction in the bearing. N.m. The average magnitude of the couple due to kinetic friction in the bearing is [
Only need A, B, and C please.
The rotor of an electric motor has an angular velocity of 3600 rpm when the load and power are cut off. The 120-lb rotor, which has a centroidal radius of gyration of 9 in., then coasts to rest. Knowing that kinetic friction results in a couple of magnitude 2.5 lb·ft exerted on the rotor, determine the number of revolutions that the rotor executes before coming to rest.
Part A The 21-kg roll of paper has a radius of gyration kA = 90 mm about an axis passing through point A. It is pin supported at both ends by two brackets AB. The roll rests against a wall for which the coefficient of kinetic friction is u = 0.2. Neglect the mass of paper that is removed. (Figure 1) Determine the magnitude of the constant vertical force F that must be applied to the roll to pull off 1 m of paper in t = 3 s starting from rest. Express your answer to three significant figures and include the appropriate units. TH HẢ ? F = Value Units Submit Request Answer Provide Feedback Figure < 1 of 1 300 mm 125 mm
The rotor of an electric motor has an angular velocity of 4500 rpm when the load and power are cut off. The 75-kg rotor, which has a centroidal radius of gyration of 200 mm, then coasts to rest. Knowing that kinetic friction results in a couple of magnitude 4.5 N m⋅ exerted on the rotor, determine the number of revolutions that the rotor executes before coming to rest. (Final answers should be in two decimal places with correct units)