The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1077.4 Nm, U = 4657 Nm, x = 27.79 m, y = 17.37 m, z = 1.31 m, d = 93 mm, and e = 77 mm, find the maximum shear stress (in Pa) in the shaft. Round off the final answer to two decimal places. U T ... Aluminum Steel Bronze e

The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1077.4 Nm, U = 4657 Nm, x = 27.79 m, y = 17.37 m, z = 1.31 m, d = 93 mm, and e = 77 mm, find the maximum shear stress (in Pa) in the shaft. Round off the final answer to two decimal places. U T ... Aluminum Steel Bronze e

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
None
Q3: Three segments of elliptical solid steel section, circular solid aluminum section and circular solid bronze section were assembled to form the shaft shown in Figure (3). Determine the generated stress in each material when the support at D is able to rotate until 0.035 radian based on the two torques T1 and T2 of 450 N.m and 750 N.m, respectively. 94= 834 v5? AL:28 1 Steel Ahminum Bronze T2 D= 70 mm D= 100 mm 1.5 m 1.5m 2.0 m 25 mm Figure (3) 145 mm
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Please show all steps so your process is easy to follow
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
4. A rigid block of having a weight M is suspended by symmetrically placed rods. Each copper rod has an area of 1200 sq.mm: E= 125,000 MPa and the allowable stress is 90 MPa. The steel rod has an area of 1500 sq.mm; E 220GPa; and the allowable stress is 120 Mpa. Determine the largest weight M which can be supported by the rods. 8c=8s Copper 160 mm Pc Ps Steel 240 mm TIT Pc ..initial level Tinal level Copper 160 mm
4. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown in the figure together with the given section properties. The torque of 1000 N-m is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly. Answer: TĄ = 5.57 MPa Ts = 22.0 MPa 3 m 1.5 m Ta Aluminum Steel 75 mm dia. T=1.0 kN•m Ga- 28 GN/m²? 50 mm dia G, - 83 GN/m?
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?