Suppose a circuit is required to recognize the 4-bit pattern (0011), and the output (z-1) whenever it occurs in the continuous serial input (X) of the circuit. 1- Draw the mealy state diagram. 2- Write down the state table. 3- Check state reductions. 4- Assign binary values to the states. 5- Obtain the binary-coded state table. 6- Select the T flip-flops in your design. 7- Derive the simplified flip-flop input equations and output equations. 8- Draw the logic diagram.

Suppose a circuit is required to recognize the 4-bit pattern (0011), and the output (z-1) whenever it occurs in the continuous serial input (X) of the circuit. 1- Draw the mealy state diagram. 2- Write down the state table. 3- Check state reductions. 4- Assign binary values to the states. 5- Obtain the binary-coded state table. 6- Select the T flip-flops in your design. 7- Derive the simplified flip-flop input equations and output equations. 8- Draw the logic diagram.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-bit counter counts in the sequence: 001, 011, 010, 110, 111, 000, 100 and repeats. Draw thelogic diagram for a circuit that implements this. Use D flip-flops. Please explain your process.
1) by creating the state table for the state diagram given below a) draw logic diagrams by designing Sequential Circuits with JK Flip flops. b)Draw logic diagrams by designing Sequential Circuits with D-Type Flip flops.
try first part plesase
A-Consider a digital counter that counts 0 to 7 when the reset button is 0 and go back to 0 when the reset button is 1. draw the state diagram and state table for the digital control circuit of such a digital counter? B-For the resulted design in A how many configurable logic block (CLB) you would need to implement your design in the FPGA if the CLB structure is as follows: Look-Up Table MUX SET (LUT) CLR
Design a state diagram to detects 0010100 overlapping input sequence (repeating). The output is at logic level "1" when the sequence is detected, Otherwise the output is "0".
create the schematic needed for part b and c please
The objective of the activity is to determine the design of the logic gates for the BCD to a 7 segment display. You do not need to implement your design. 1. Show the truth table for BCD to 7 segment display. (4 bit input, with all outputs, a-g and the corresponding decimal digit) 2. Show the K-map and minimized boolean function for each output. 3. Show the logic diagram of the decoder. (You may use a CAD for this or if you do not have one, you may submit a handwritten one.) This is a very common decoder and there are many sites covering requirements 1-3. However, it would be best if you go through the design by hand as an exercise from the truth table to don't cares in K-maps.
Design a 4 bit Modulo-9 counter (i.e. the counter goes up till 8 only andthen goes back to 0). Clearly show all the design steps. Use only T-flip flops.Only diagrams as solution to this question are not acceptable.
create the schematic needed for part d please
Using T-type flipflops, design a counter by counting the binary sequence of 7, 5, 3, 1, 0, 2, and then back to 7 by creating Karnaugh diagrams, and draw the logic circuit. If there is a situation that prevents the counter from working properly in binary situations (such as the two states constantly looping over each other), what solution should be made to overcome this situation? If there is such a case, correct the counter design according to your suggestion and show the design that will enable it to count correctly by correcting the status table. If this is not the case, do not make any changes. NOTE: The state variables are A, B, and C. Flip flop inputs are TA, TB and TC. Q(t+1) =Qn+1= Qn ⨁ TTFull Screen Reader for a T-type FF
For a sequential logic circuit that detects 010011 sequences in binary information received from an external input line x and makes external z output 1 when detected; a) Create the state diagram. Explain how you created it. b) Create the situation table. Note: D flip-flops are used in this circuit. If there are unused states in the state table, you can specify the next state values and output them as inactive values.