STEEL STRUT e BASE PLATE CONNECTOR PLATE ANCHOR BOLT 8.617 mm thick Steel strut is connected to the 12.090 mm thick connector plate using a 16.629 mm diameter pin. 4-16.579 diameter anchor bolts then fastens the base plate. Determine the bearing stress between the pin and the strut if P is 48.10 kN.

STEEL STRUT e BASE PLATE CONNECTOR PLATE ANCHOR BOLT 8.617 mm thick Steel strut is connected to the 12.090 mm thick connector plate using a 16.629 mm diameter pin. 4-16.579 diameter anchor bolts then fastens the base plate. Determine the bearing stress between the pin and the strut if P is 48.10 kN.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.2P

See similar textbooks

Similar questions

Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
I NEED ANSWER
6. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24mmp A490N bolts. The plate is A36. Determine the safe load Pu using LRFD that the truss can resist according to the capacity of the connection. 15 15 с 1.5 3P. + D 1.5 80 mm 70 mm 70 mm 80 mm Fac 7. Repeat Problem 6 using 30mm A325-N bolts and A-50 steel. Use ASD. 50 mm Fac
SOLVE FOR THE FORCE IN MEMBERS AB, AC, BC, CD, BD, BE, DE, DF & EF. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND WRITE WELL ALSO SEE LINK UNDER WEEK7 0.8m 2.4m -6KN MEMBER AB AC BC CD BD BE 2m ED DF EF 1m 8KN Av REACTION hinge) EX REACTION @roller) 3m SUMMARY OF RESULTS FORCE 1m 10KN 2.4m 3KN NATURE(I or C)
4. Six rivets are used in the connection shown in the figure. If both P= 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Ps so 100 mm
A C8x11.5 single channel section us bolted to a gusset plate with M22 bolts. Assume A36 steel, 5.6 mm thick web for the channel and an 8mm gusset plate. U=0.80 The channel has a gross area of 2181 mm^2. The bolts have a shear stress of 457 Mpa. What is the design tensile strength due to gross yielding (kN)?
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine: a. The shear stress in the bolts. Answ. 11.81 ksi b. The axial stress in the bolts. Answ. 23.62 ksi c. The support stress in the W12X65 profile. 11.50 ksi
A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe
2. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24 mm diameter A325N bolts. The plate is A50. Determine the safe load Pu using ASD that the truss can resist according to the capacity of the connection. LS 15 WR + 14 DATE ON ON Mmm 70 m 40 mm
Situation 13: A square hollow strut of thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to the concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. 48 KN steel strut - 30° base plate connector plate anchor bolt 40. Which of the following most nearly gives the bearing stress between the strut and the pin? а. 150MPа с. 120МPа b. 140MPA d. 125MPA 41. Which of the following most nearly gives the shearing stress in the pin? a. 110.46MPA с. 103.37МPа d. 119.37MPA b. 126.39MPA 42. Which of the following most nearly gives the shearing stress in the anchor bolts? а. 55.04MPа c. 51.69MPA b. 59.68MPA d. 47.16MPA
Problem 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing stress due to rivets is 140 Mpa • Thickness of the member is 5 mm • Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 N 120 N 200 N 4 Pands 4m - 16 m
SOLVE FOR1 HR