2. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24 mm diameter A325N bolts. The plate is A50. Determine the safe load Pu using ASD that the truss can resist according to the capacity of the connection. 3P. 15-- 1.515 - 1.5 D M:

2. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24 mm diameter A325N bolts. The plate is A50. Determine the safe load Pu using ASD that the truss can resist according to the capacity of the connection. 3P. 15-- 1.515 - 1.5 D M:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V
can you explain pls how we find 12(removed connection) part??
The bearing-type-in. A325 bolts of the connection of Fig. have an al- lowable strength = (0.6)(30) = 18 k. Locate the instantaneous center of rota- tion of the connection, using the trial-and-error procedure, and determine the value of P. O O -5 in. F O +3 in. O P 6 in.
Determine the maximum factored load P, that can be carried by the connection shown in the Figure P7. 1. The weld is 6 mm fillet weld. All structural steel is A36. E70 electrode is used
Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material :fy = 480 MPa, fu = 560 MPa, Members are S235) a Section a-a 10 mm 10 cm P { =37.14 mm 5 cm 16 mm Gusset Plate a
Using SMAW process, E70 electrodes and an A572 steel. Determine thelength of the side fillet welds for the full capacity the 125x100x10mm angle tensionmember as shown below. Assume that the member is subjected to repeatedstress variations making any connection eccentricity undesirable. Check theblock shear strength of the member. Assume that the WT chord has sufficientstrength to develop the weld strengths and the thickness of its web is 12mm. UseU = 0.87 for class use and LRFD Method only.
Complete solution pls
The three-plate moment connection shown below are all shop- welded- to the column and then field bolted to the girder. The beam is a W18 55 that has a factored moment of Ma = 382 kip ft and a factored shear of V. = 65 kip. All plates are A36 steel (E = 36 ksi, Fu = 58 ksi). Plate 2 is connected to the girder using four bolts as shown. All bolts for the connection are 7/8" diameter A325-X. Plate 1 Plate2 2.00" 2.75" W18 55 2.75" 2.75" 2.00" `Plate3 3.00" 2.50" (a) Design Plate 1, including the required number of bolts and dimensions of the plate. Assume an E70XX weld to the column. Consider limit states only for the plate itself. That is, you do not need to consider limit states for the beam or column. (b) For which plate(s) will you need to check the buckling capacity, Plate 1, 2, and'or 3? Explain.
intel com Deter mine all force members O* the truss Shown 3m bo0 N Cx - 600N
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
Determine if the members AL, AB, FG, FH, and BL are under zero-force membercompressed membertensile membernot a member