Situation 13: A square hollow strut of thickness 10mm is pin connected to two connectorplates of thickness, 12mm. The connector plates are welded to the base plate of thickness,12mm. The base plate is fastened to the concrete base by 4-16mm diameter anchor bolts. Thediameter of the pin is 16mm.48 KNsteel strut -30°base plateconnector plateanchor bolt40. Which of the following most nearly gives the bearing stress between the strut and thepin?а. 150MPас. 120МPаb. 140MPAd. 125MPA41. Which of the following most nearly gives the shearing stress in the pin?a. 110.46MPAс. 103.37МPаd. 119.37MPAb. 126.39MPA42. Which of the following most nearly gives the shearing stress in the anchor bolts?а. 55.04MPаc. 51.69MPAb. 59.68MPAd. 47.16MPA

Given, Load acting on the strut, say P = 48 kN = 48000 N Thickness of strut, say ts = 10 mm…

Answered: Situation 13: A square hollow strut of…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A built up section of A992 steel, F, = 345 mPa is made from plates fully welded together. The flanges consist of PL16X380 and PL12X500 for the web. Use the NSCP 2015 specifications. PL16x380 WL = 1.5wp %3D A Wu = 3.6wp 10m Which of the following best gives the maximum service dead load, wp? 40.2 kN/m 26.8 kN/m O 10.8 kN/m O 96.6 kN/m PL12x500
The five-bolt connection shown must support an applied load of P = 300 N. The thickness of the axial member: = 1.5 mm. and the width = 18 mm If the ultimate shear stress in the bolts must be limited to 265 MPa with F.O.S = 3.7 . And the ultimate normal stress in the axial member = 250 MPa, with F.O.S = 2.8 , And the ultimate bearing stress in the axial member = 110 MPa, F.O.S = 2.5 Determine the minimum bolt diameter that may be used in the connection
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
figure A 2m """" B 2 m C ** 2 m E 4 m D 700 N 500 N 2 of 2 > ▼ Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. EF FG ODF П П П □ DE AB ВС BC AG CG CD BG CF Submit Provide Feedback Request Answer
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
Determine the smallest allowable diameter for a circular cross-sectional area of members BD, BE and CE of the truss shown. The working normal stresses are 2000 psi in tension and 1200 psi in compression. (A reduced stress in compression is specified to reduce the danger of buckling.) 12 t 40 kips
Calcualte the following: Total factored floor load in 2 decimal places, ___ kPa Total factored uniform load on girder GH in 2 decimal places, ___ kN/m Maximum ultimate bending moment at discontinuous end of girder JK to the nearest whole number = ___ kN·m
Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.35 in.² and a yield strength of 45 ksi. The pins at B, C, and D each have a diameter of 0.7 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.5 with respect to its yield strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 46 in. and b = 94 in. D (1) b A kips P Answer: Pallow= i a B
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
The lap joint is fastened with four ¾ inch diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
The truss below is pin connected at A and E, and is acted on by the forces shown. E A D B Identify all of the ZERO-FORCE MEMBERS by checking the boxes below (if there are none, leave all boxes unchecked): BF AF BC BH CD EG -GH AB CH DG DH DE -FH

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS