Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.35 in.- and a yield strength of 45 ksi. The pins at B, C, and D each have a diameter of 0.7 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.5 with respect to its yielc strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 46 in. and b = 94 in. D (1) b P B

Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.35 in.- and a yield strength of 45 ksi. The pins at B, C, and D each have a diameter of 0.7 in. and an ultimate shear strength of 78 ksi. Each pin connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.5 with respect to its yielc strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 46 in. and b = 94 in. D (1) b P B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 20 2okN KN Hinge B I the max nagative bonding momut at A

Q: Three steel plates are joined by three 20-mm diameter rivets. If the ultimate shear stress in the…

Q: 60 b P P 150 100 100 100

Q: An aluminum alloy [E = 10,000 ksi; Oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

Q: The member is connected to a gusset plate with 10 inch longitudinal welds. Fin el shape to carry the…

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: Solution: Given: LL = 25 kN DL = 50 kN U = 1.0 Plate dimensions: 10 x 100 mm Factored load: P = 1.2…

Q: in eadh member. =s dondopad at in at C A.

A: Find distance 'x'h=122-x2=52-13-x2x=11.0769mh=122-x2=4.6154mTake moment about C:∑…

Q: An aluminum alloy [E = 10,000 ksi; Oy= 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; Oy…

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

Q: An aluminum alloy [E = 10,000 ksi; oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

Q: Which of the following DO NOT match?

A: allowable load is the maximum safe load carried by the member or material

Q: allowable

A: Block shear strength Agv =12in2×4 in= 4.00 in2Agv = 4.00 in2Ant = 12in10in = 5.0 in2Ubs = 1.0Rn…

Q: Q.1: Use LRFD method to design member (BD) in truss shown to carry the load shown in figure, use…

Q: AWT205 x 30 structural steel section (see Appendix B for cross-sectional properties) is used for a…

A: Given, WT205 x 30 section Length = 8.8 m or 8800 mm

Q: Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of…

A: Given strength of fillet weld 94 mpa Size of fillet weld = 8 mpa Load to be carried = 185 kn

Q: ISA 75 x 75 x 8 mm serves as tensile member. This angle is welded to a gusset plate as shown in…

A: Note : This question is related to Indian Standard Code as asked in the problem. Given data, ISA…

Q: -A 8teel pod is stretcke between two rugid walls ard carries a tensile Coad f GO0ON a C If the…

Q: A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL % ×…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Determine the no. of rivets to fasten the member BD

A: GIVEN: 1. Rivet strengths at working conditions : In Shear = 70 MPa In Bearing = 140 MPa 2.…

Q: D Front view 18 mm 6 mm B IB Side view 160 mm 120 mm Top view In the steel structure shown, a…

Q: Determine the zero-force members in each of the two trusses shown. E C D D B po TTTTTTTT 5 A…

Q: P6-1. In each case, calculate the support reactions and then draw the free-body diagrams of joints…

Q: THE TENSION MEMBERS IS COMPOSED OF A 200x150x10 mm THICK ANGLE CONNECTED USING 21…

A: 1. The formula to calculate the net area of the section is given by, Anet=B-ndt…

Q: Calculate the maximum shear force in the welds in the given figure. P=160KN X = 150mm y= 125mm…

Q: dentiry the shown. (Enter your separated E A

Q: Method Joints 5th Det.: a- Reactims ©A ard B 6-toce m rembers H, FH, GE, GD, ID and tE ldentify f…

A: A truss is given in the question and it has been asked to determine Reactions A and B B. Force in…

Q: Prob. 2.9-8. The steel eyebar in Fig. P2.9-8 has cross-sec- tional dimensions 25 mm x 100 mm. To…

Q: Beam AB is supported as shown in Figure. Tie rod (1) is attached at B and C which are double-shear…

A: Data Given: w = 1800 lb/ft σs = 54 ksia = 15 ftb = 30 in.c = 7 ft.fy = 36 ksiFOS = 2.5 Asked:…

Q: what should be the mini mum For the tigure s how n, dia meter OF the rivets attached as shown TF the…

A: given data allowable axial stress =60MPa allowable shearing stress = 110 MPa width of plate,b =100…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: Consider the free body diagram;

Q: An aluminum alloy [E = 10,000 ksi; Oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

Q: D 30 kN 70 kN 2 m 12 mm-thick gusset plate 10 -mm-thick 2 m angle 1.5 m-15 m- 15 m--15 m 8 mm-thick…

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place,…

Q: Which of the following best describes a plastic hinge? Section where extreme fibers have yielded O…

A: Answer- MY < M > MP Explanation - Plastic hinge can be defined as yielded zone due to flexure…

Q: Problem For the frame shown, design the maximum permissible value of P with a factor of safety of…

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P =…

Q: 2,300 mm A 1,150 mm 1,600 mm 75 kN

Q: Find the stresses of FAB. FAc. FBC & FBD- 20 k 15 k 60 60 60 60

Q: A column is formed by welding two A36 MC sections back-to- back. The column is 32 feet long. With…

A: Following are the given information. A=6.45 in2, d=10 in bf=3.32 in, x=0.990 in Ix=102 in4, Iy=6.40…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Rigid bar ABC is supported by member (1) at B and by a pin connection at C. Member (1) has a cross sectional area of 1.35 in.² and a
yield strength of 45 ksi. The pins at B, C, and D each have a diameter of 0.7 in. and an ultimate shear strength of 78 ksi. Each pin
connection is a double-shear connection. Specifications call for a minimum factor of safety in member (1) of 1.5 with respect to its yield
strength. The minimum factor of safety required for pins B, C, and D is 2.9 with respect to the pin ultimate shear strength. Determine
the allowable load P that may be applied to the rigid bar at A. Use overall dimensions of a = 46 in. and b = 94 in.
D
(1)
b
A
kips
P
Answer:
Pallow=
i
a
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable shearing stress of 55.44 MPa. The bolt will be tightened so that the axial load will be 17 KN. Find the required thickness of the bolt head if the thread is 0.25 mm deep.
DO NO OWAVE www.oukpak.com F06 unic 30KN 150 KN 20KN 3m =30" SOLVE FOR ACL SUPPORT 2m HINGE REACTIONS LN DICATE THE DIRECTICNS e UNITC 20 A B im
IDENTIFY THE ZFM ZERO FORCE MEMBERS
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
Find the stresses in A, B and C? 14-d Vem 14 6m 0.006 MN 0 cm B -HA- 4 IX 6em H
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Problem 2: Book Problem 3-9 (Hint: Only one of the two chains is at max tension, the other will be less.) 3-9. Determine the maximum force F that can be supported in the position shown if each chain can support a maximum tension of 600 lb before it fails. 30° SERDISC A Prob. 3-9 C
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear