Steam enters a turbine at 3 MPa and 600 C and leaves at 100 kPa and 100 C. In the process, it losses 150 kW of heat to the surroundings. The mass flow rate of steam going through the turbine is 2 kg/s. Find the amount of power in kW generated by this turbine. Enter the absolute value. 2014 857 O 1007 4

Steam enters a turbine at 3 MPa and 600 C and leaves at 100 kPa and 100 C. In the process, it losses 150 kW of heat to the surroundings. The mass flow rate of steam going through the turbine is 2 kg/s. Find the amount of power in kW generated by this turbine. Enter the absolute value. 2014 857 O 1007 4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Air (MW=29 kg/kmol) at 115.00 kPa and 285.00 K is compressed steadily to 600.0 kPaThe mass flow rate…

A: The inlet temperature of the air, The inlet pressure isThe exit pressure is The heat loss, The…

Q: water vapor enters an adiabatic turbine at a pressure of 6 mPa and a temperature of 500 C, the…

A: Steam inlet pressure, P1=6 MPa Steam inlet temperature, T1=500oC Steam outlet pressure, P2=100 kPa…

Q: A steam turbine produces 3,100 kW of power. The steam enters the turbine at 10 MPa and 500 C. The…

Q: Air flows steadily at the rate of 1 kg/s through an air compressor at 10 m/s, 100 kPa and 1 m3/kg…

A: The rate of work done is -259.968 kW. (Negative sign indicates, work input is required to drive the…

Q: A device submitted to the Pa- tent Office is shown schemati- cally in the figure to the right. Its…

A: To determine if steady-state operation of this device is thermodynamically permissible, we need to…

Q: Calculate the work W done by the gas during process 1→2

A: WORK DONE BY GAS Thermodynamic system work is done when under external pressure it expands…

Q: Exercise-2 Steam enters a nozzle at 400 deg C and 800 kPa with a velocity of 10 m/s, and leaves at…

A: Given : At inlet of nozzle 1 : At exit of nozzle 2: here negative sign represent the heat loss .…

Q: A heat source at 600 K loses 1000 kJ of heat to a sink at 300 K. The Entropy generated in this…

A: Given data as per question Temperature of heat source=600 k heat=1000 kjtemperature of sink =300 kwe…

Q: The boiler of a steam generator has a total volume of 2 m3, and initially contained 1.5 m3 of water…

A: Below is the pictorial representation of the given question Given data:- The volume of vapour=0.5…

Q: 1. A vertical cylinder fitted with a piston contains 5 (kg) of R134a at 12°C. Heat is transferred at…

Q: 53.4 lbm of air in a rigid container at 22 psia and 400 R absorbs 3.04127 kW*hr of energy from an…

Q: Consider the system shown in the figure. When the pins fall away, the gas expands against a constant…

A: Number of moles of the gas, n=10 Initial pressure Pi= 5atm External Pressure Pext = 1 atm T = 300 K…

Q: In the interior of a piston that can move freely, there is initially 2 kg of R-134a refrigerant in…

Q: Water enters a pump as saturated liquid 50 kPa at a rate of 3.0 kg/s and exits with a pressure of 10…

Q: A gas cylinder with interior volume 11.6 L holds compressed air at 17.4 MPa. The cylinder is joined…

A: Given: Volume of the gas cylinder: →V1=11.6 L=0.0116 m3 Pressure in the gas cylinder: →P1=17.4 MPa…

Q: A piston-cylinder device initially contains CO2 at 200 kPa and 400°C and the total enclosed volume…

Q: R-410A

A: V=10l=.01m3T1=-10oCx1=.8T2=40oCWe=36kJ/kg from the R140 saturation table at T1=-10oC…

Question

Steam enters a turbine at 3 MPa and 600 C and leaves at 100 kPa and 100 C. In the
process, it losses 150 kW of heat to the surroundings. The mass flow rate of steam
going through the turbine is 2 kg/s. Find the amount of power in kW generated by this
turbine. Enter the absolute value.
2014
857
O 1007
1864
4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. Air with a pressure of 2 MPa and a temperature of 250 C (0.5 kg of PV^ 1.25 = expands while satisfying a certain relationship. Find the work done during this process when it expands until the temperature reaches 330 K.
We take a 33 kg chunk of ice (Temp is 0°C) and submerge it in an isolated container. This container has 6 kg of water, and the water is 7°C. Answer the following: 1) How much ice from the block melts (in grams)? 2) What is the change in entropy for the entire system?
A piston-cylinder device initially contains CO2 at 200 kPa and 400°C and the total enclosed volume is 300 litres. Due to heat loss, the piston moves downwards to a position where it sits on a pair of stoppers and its final enclosed volume is 150 litres. Further heat loss leads to the pressure being reduced to 160kPa. Workout 1) the final temperature, 2) the total work done by CO2 and 3) the total heat transferred to CO2. Also make some comments on the result of heat and create a schematic p-v diagram of the process. The following assumptions are to be made: CO2 is a perfect gas and its molecular mass is 44kg/kmol. The ratio of specific heat capacities, γ (gamma) is 1.3 The volume occupied by the stoppers is to be ignored. There is no leakage in the system There is no friction between the cylinder and piston walls and the piston moved slowly at the same speed therefore, no acceleration. For the conversion from Celsius to Kelvin, use 273 Use 8314.5 J/kmol.K for the universal gas…
Q4\closed system of 2kg undergoes adiabatic process. The work done on the system is 30000 J. if the relation velocity during the process is (V2² - V12= 216 ) the elevation of system increase from 32M to 77M. Determine the change in internal energy of the system
2. If a gas of volume 6000 cm³ and at pressure of 100 kPa is compressed quasistatically according to PV? = constant until the volume becomes 2000 cm³, determine the final pressure and the work transfer.
An air compressor takes in air at a pressure of 100 kPa and a temperature of 300 K. The compressor is cooled at a rate of 15 k/kg and the mass flow rate is 50 kg/minute. The air leaves at a pressure of 600 kPa and a temperature of 420 K. What is the work that needs to be input to the compressor to achieve this rate of flow? You may use a cp of 1.006 k/kg-K. Give your answer to three significant digits in kilowatts.don't put kw in your answerl) COMPRESSOR SECTION Compressor housing Compressor a dicharge Compreor anbient a Compreor wheel
The valve connected to a 450-liter insulated tank of air at 250 kPa and 50̊C is opened,allowing the gas to escape until its pressure drops to 120 kPa. An electric heater insidethe tank maintains the temperature at 50̊C. Using variable specific heats, Determine thefollowing:a) The mass of air withdrawn (kg)b) The energy input to the resistor (kJ)
Initially, 200 L of saturated vapor refrigerant-134a in a piston. The piston is free to move, and its mass is such that it maintains a pressure of 900 kPa on the refrigerant. The refrigerant is now heated until its temperature rises to 60°C. The work done during this process is Select one: 73.55 kJ 37.55 kJ 27.49 kJ O 72.49 kJ
Steam is operating a turbine. The mass flow rate of steam is 1.5 kg/s. The steam is entering at 2 MPa, 350C and is leaving at 0.1 MPa with a quality of 100%. During this process, 5 kW of heat is lost by the turbine. Determine the work produce by the turbine.
Steam expands in a turbine from 6 Mpa and 500 Celsius to 0.2 Mpa and 150 Celsius at a rate of 1.2kg/s. Heat is lost from the turbine at a rate of 34KJ/s during the process. Find the power output of the turbine.
As shown in the figure below, water behind a dam enters an intake pipe at a pressure of 24 psia and velocity of 5 ft/s, flows through a hydraulic turbine-generator, and exits at a point z1 = 260ft below the intake at 19 psia, 45 ft/s, and a specific volume of O.01602 ft3/lb. The diameter of the exit pipe is 5 ft and the local acceleration of gravity is 32.2 ft/s?. Water Dam P1 = 24 psia Vj =5 ft/s Generator i Turbine P2 = 19 psia v = 0.01602 ft³0b V2 = 45 ft/s D =5 ft Water Evaluating the electricity generated at 8.5 cents per kW · h, determine the value of the power produced, in $/day, for operation at steady state and in the absence of internal irreversibilities. Value = $ i /day