Steam at a velocity of 60 m/s and 250°C and 7 bar absolute is expanded through a nozzle to 200 C and 5 bar. The nozzle has rigid (non movable) walls and its function is to increase the kinetic energy. Negligible heat is transferred from the nozzle to its surroundings. 1. Calculate the exit stream velocity? 2. Calculate the temperature and quality of the exit steam if it leaves the nozzle at a velocity of 720 m/s and a pressure of 5 bar

Steam at a velocity of 60 m/s and 250°C and 7 bar absolute is expanded through a nozzle to 200 C and 5 bar. The nozzle has rigid (non movable) walls and its function is to increase the kinetic energy. Negligible heat is transferred from the nozzle to its surroundings. 1. Calculate the exit stream velocity? 2. Calculate the temperature and quality of the exit steam if it leaves the nozzle at a velocity of 720 m/s and a pressure of 5 bar

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam (water vapor) enters a stainless steel tube with inner diameter 4cm at 300°C and 60 bar absolute pressure, with a velocity of 8.00 m/s. The steam exits the tube at 300°C and 40 bar absolute pressure. a. Assuming the water vapor behaves as an ideal gas, calculate the steam mass flow rate and the change in kinetic energy (in Watts). b. Using the specific volume values from table B.7, calculate the steam mass flow rate and the change in kinetic energy (in Watts).
The feed to a compressor is superheated steam at 310°C and 40 bar. It enters the compressor at a velocity of 17 m/s. The pipe inlet inside diameter is 0.25 m. The discharging pipe, after the compressor, has a smaller inside diameter and the discharge velocity is 120 m/s. The exit of the compressor is superheated steam at 350°C and 85 bar absolute. Heat loss from the compressor to the surroundings is 3 kW. Determine the compressor horsepower
Air (MW=29 g/mol) at 115.00 kPa and 285.00 is compressed steadily to 600.0 kPa. The mass flow rate of the air is 2.00 kg/s and a heat loss of 32.1 kW occurs during the process. You may assume that changes in kinetic and potential energy are negligible, the temperature of the surroundings is 25 ∘C, and that the CP of air is 3.5 R. Given the compressor operates with a second law (reversible) efficiency of 0.60,calculate the following. What is the actual work interaction term in kW? What is the actual exit temperature of the air in Celcius?
Air enters a turbine at temperature and pressure of 800°C, 10bar respectively. The actual exit airtemperature is 180°C. The turbine isentropic efficiency is estimated to be 85%. Calculate the turbine exit pressure and the actual expansion index (n).
Q.3 A steel bar at a temperature of 500°C is dropped into an insulated bath containing 20 kg water at 120°C. The temperature of water and Steel reaches steadily to 150°C. If specific heat for water is 4 .180 kJ/kg-K, calculate the change in entropy of system.
An insulated tank A of 0.6 m3 volume is connected to an insulated tank B of 0.3m3 volume. Initially, tank A contains steam at 0.2 MPa and 200 °C, and tank B contains wet steam at 0.5 MPa and 85% quality. The valve is opened and flow occurs until equilibrium (both mechanical and thermal) is attained. Estimate the final pressure.
Give the significance of volume coefficient. The volume coefficient of expansions of water at 373 K is 7.8 x 10-4 K-1. Calculate the change in entropy when the pressure is increased from 1 bar to 100 bar. At 373 K, density of water is 958 kg/m3 .
Oxygen with mass m = (0.08kg) in V1 volume has transformed into V2 = (V1 / 4) by isothermal compression. Later, oxygen was heated at constant pressure and its volume turned into V3 = (5V2). Plot this process on a p-V graph and calculate the total entropy change. (consider oxygen the ideal gas.) (molar heat capacity of oxygen at a constant volume Cv = (5/2) R)
Air enters an adiabatic nozzle at 400 kPa and 900 K with negligible velocity . If the flow is ideal and exit pressure is 100 kPa, find the exit temperature in K and the exit velocity in m/s.
3. A mass of 0.25 kg of air at 400 °C and 0.9 bar absolute is compressed at constant temperature to 2 bar absolute. The pressure is then dropped at constant volume back to the initial pressure of 0.9 bar absolute. For the total mass of air, calculate the change in entropy, the heat supplied and the work output. Sketch the process on a Ts diagram. (20 marks)
Please show your complete solution. Thank you! During the reversible process executed by the non-flow system, the pressure increases 334.79 kPa to 1378.96 kPa in accordance with PV=C and the internal energy increase is 22, 577 J, the initial volume is 85 liters. Find the heat.
A saturated steam at 400kPa enters the turbine and exits as saturated liquid at 80o C flowing at 0.2m/s. If both inlet and outlet pipes have a diameter of 12.5cm, calculate the work produced in the operation. Perform Degree of Freedom analysis.