nozzles at a 7. steam enters a group of convergent-divergent pressure of 2.2MPa and with a temperature of 260C. Equilibrium expansion through the nozzles to an exit pressure of 0.4MPa. Up to the throat the nozzles the flow can be assumed as frictionless. From throat to exit, however, there is an efficiency of expansion of 85%. The steam flow through the nozzles is 11 kg/sec. Find (a) the throat and exit velocity, (b) (548m/sec, 800m/sec, 32.1 cm², 60.5cm²) the throat and exit areas.

nozzles at a 7. steam enters a group of convergent-divergent pressure of 2.2MPa and with a temperature of 260C. Equilibrium expansion through the nozzles to an exit pressure of 0.4MPa. Up to the throat the nozzles the flow can be assumed as frictionless. From throat to exit, however, there is an efficiency of expansion of 85%. The steam flow through the nozzles is 11 kg/sec. Find (a) the throat and exit velocity, (b) (548m/sec, 800m/sec, 32.1 cm², 60.5cm²) the throat and exit areas.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

100% High pressure water and compressed air are delivered to some operating rooms. Bored one day, with no patients around, you take the cap off the nozzle to see what would happen. Water flows through the vertical pipe and nozzle and then exhausts into the air as shown in the diagram. The water pressure in the pipe at position 1 is 3 atm. The pressure when the water discharges to the air is 1 atm. Position 2 identifies the nozzle, 0.75 m above position 1, where the water flow has been constricted from an 8-cm diameter pipe to a 3-cm diameter nozzle. Assume that the free jet remains a stream of water with a 3-cm diameter. Assume no friction losses. Free jet -3 cm diameter 0.75 m a) Determine the mass flow rate of water through pipe at position 1 in kg/s. 3 atm 8 cm diameter b) Determine the height, h, the water jet can rise. c) Calculate the friction factor inside the 8-cm pipe and determine if the assumptions of negligible friction losses was reasonable. Water AR d 128 PM 10/3/2021…
Hi please help me answer this question with complete solution
Air enters a turbine at temperature and pressure of 800°C, 10bar respectively. The actual exit airtemperature is 180°C. The turbine isentropic efficiency is estimated to be 85%. Calculate the turbine exit pressure and the actual expansion index (n).
Apply the first law of thermodynamics to nozzle. Assume that the process is reversible adiabatic. Draw the neat sketch and lable inlet and outlet properties
Q4. Fluid enters a condenser at the rate of 40 kg/min with a specific enthalpy of 2000 kJ/kg, leaves with a specific enthalpy of 200 kJ/kg. The condenser cooling water flows at the rate of 730 kg/min and its gain specific enthalpy in passing through the condenser is 90 kJ/kg. Determine the rate of heat energy loss to the atmosphere. 05 Calculate the air standard efficiency and work of an Otto cycle has a clearance volume of
an air compressor of three stage compresses air from 100 kpa to 1000 kpa. calculate the intercooler pressure between the first and second stage
Solve it correctly please. I will rate accordingly with 3votes.
a turbojet on a test stand air at inlet has density of 1.1 kg/m^3 at the exit gas has higher velocity and higher temp, but pressure is the same. inlet area is 0.5m^2 and free stream velocty is 200m/s. fuel air mix is 1:15 at exit, engine area is 0.3m^2, gas velocity 800m/s Determine the density of gas at exit and evaluate reaction forces to hold test stand Turbojet Engine V1 V2 P2 A1 A2 Test Stand
A steady stream of n-butanol is needed to be fed into the reactor at 40 ̊C. However, the inlet of the reactor is located 7.5 m above the reservoir tank. As such, a highly effective centrifugal pump (70% efficiency) is used for such a purpose. It was understood that the needed volumetric flow rate into the reactor is fixed at 20 m3/h. It was also noted that the n-butanol reservoir is closed but not pressurized, while the gauge pressure at the endof the discharge line is measured at 275 kPa. Given that the density of n-butanol is 810kg/m3. If the discharge pipeline was 5 cm in diameter, calculate: (i) The velocity of n-butanol at the discharge line. (ii) The total power input from the centrifugal pump. (iii) The power delivered to the n-butanol fluid.
Choose the following and define also
Q4) The nozzles receive steam at 1.75 MPa, 300 °C, and exit pressure of steam is 1.05 MPa. If there are 16 nozzles, find the cross-sectional area of the exit of each nozzle for a total discharge to be 280 kg/min. Assume nozzle efficiency of 90%. If the steam has velocity of 120 m/s at the entry to the nozzles, by how much would the discharge be increased?
Solve it correctly please. I will rate accordingly.