Saturated steam at 10 bar pressure is supplied to increase the temperature of the feed natural gas from its inlet temperature of 30°C to within 15°C of the steam outlet temperature. All steam properties can be verified in the steam table, attached. Evaluate the mass flow rate of the steam supplied, if about 20% of the steam is still uncondensed at the exit. The relevant properties of Natural gas (NG) are as follows: NG Flow Rate = 1500 kMol/hour Average specific heat Capacity of NG = 40 kl/kMol.°C.

Saturated steam at 10 bar pressure is supplied to increase the temperature of the feed natural gas from its inlet temperature of 30°C to within 15°C of the steam outlet temperature. All steam properties can be verified in the steam table, attached. Evaluate the mass flow rate of the steam supplied, if about 20% of the steam is still uncondensed at the exit. The relevant properties of Natural gas (NG) are as follows: NG Flow Rate = 1500 kMol/hour Average specific heat Capacity of NG = 40 kl/kMol.°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q) Water flowing through a tube of 1.5 cm diameter is heated from 70°F to 88°F while the tube surface is maintained at 71°C. If the mass flow rate of water through the tube is 79.4 Ib/min, calculate the length of the tube.
6. A working area of a mine has diesel equipment operating within it. The maximum diesel loading is 750 kW. The same section of the mine also has a methane inflow of 0.25 m³/s flowing into it. If the maximum permissible methane concentration in the general body of the air is 0.5% and the design diesel air quantity is 5 m³/s per 100 kW of installed diesel power, determine the required ventilation flow rate for the working area.
Please don't give image based answer..thanku Question:- Water vapor enters a continuous flow adiabatic turbine at 9 MPa pressure, 450 o C temperature and 188 m/s velocity, and exits at 50 m/s speed at 20 kPa pressure and 92% dryness. Calculate the turbine inlet cross-sectional area since the mass flow rate of the steam is 12kg/s.
The equivalent evaporation (kg/hr) of a boiler producing 2000 kg/hr of steam with enthalpy content of 2426 kJ/kg from feed water at temperature 40°C (liquid enthalpy = 168 kJ/kg) is (enthalpy of vaporization of water at 100°C = 2258 KJ/kg) %3D %3D
the question below is already answered in the photos that I provided I only want to ask how did it find the answersSaturated steam at a pressure of 25 psia is sprayed into a stream of moist air. The initial condition of the air is 55 dry-bulb temperature and 35 F de-point temperature. The mass rate of air flow is 2000 lb per min. Barometric pressure is 14.696 psia. Determine how much steam must be added in lb per min to produce a saturated air condition, b) the resulting temperature of the saturated air.my question here is:regarding of the solution pls elaborate how did it get w1 and h1 is it given in the psychrometric chart or it has a specific solution to follow
For air properties use online source: https://www.peacesoftware.de/einigewerte/luft_e.html The compressor is operating at steady-state increasing pressure of R-22 refrigerant from 4 bars to 14 bars. Temperature was rising during the process from 12C to 90C. The inlet volumetric flow rate is 1 m3/min and inlet diameter is 0.03m. At the exit the diameter is the same. Heat flow to the surroundings can be neglected. Determine: a.Mass flow rate [kg/s] SHOW AND EXPLAIN ALL STEPS PLEASE
Physics Consider a tank full of gaseous propane at 25 ºC and 5 atm. The tank is accidentally damaged resulting in a 10-mm hole. Calculate the mass flow rate of propane through the hole (assume that the pressure in the tank remains at 5 atm and that the ambient is at atmospheric pressure). NB: the ratio of specific heats for propane is 1.15
Imagine that you have a rigid leak-proof container that contains nitrogen (N2) gas at atmospheric pressure and room temperature (25 °C). Now imagine that a small quantity of liquid water is added to the chamber without letting in any outside air. After some time, the air in the container is tested and is found to contain not only nitrogen gas but water vapor as well – even though the temperature never rose above 25 °C – and that the total pressure in the container increased to 1.30 atmospheres. Assuming all gasses are acting like ideal gasses, (i) calculate the final pressure of nitrogen and water vapor in the container and (ii) state what these individual pressures are called.
For an exhaust valve of 1.43 * 10-3 m? effective area, calculate the mass flow rate through the valve (SI unit). The flow coefficient is 0.65 and the cylinder pressure and temperature are 625 kPa and 820 K. Assume exhaust system pressure is 103 kPa, the specific heat ratio is 1.4 and R =287 J/ kg.K.
HMW-3 Combustion in a diesel engine is assumed to begin at TDC and proceed at constant pressure. The air/fuel ratio is 27/1, the calorific value of fuel is 43 MJ/kg, and the specific heat of combustion products is given by: Cy = 0.71 + 20x10-5 T where T is the combustion products temperature in K unit. The gas constant for these products is taken to be 0.287 kJ/kg K. If the compression ratio is 15/1, and the temperature at the end of compression is 870 K, find at what percentage of the stroke the combustion is completed.
A Stirling engine: (1) isothermal heat addition → (2) isochoric heat removal → (3) isothermal heat removal → (4) isochoric heat addition; uses one mole ideal rigid diatomic gas and operates between a hot and a cold reservoir at temperatures TH 600 K and To = 300 K, and a volume of V₁ = 1 L and V/₂ : = 4 L. Calculate the heat removal/addition in part (4) of the cycle. Select one: a. Q b. Q O c. Q O d. Q = = = = -6236 J 6916 J Q=-3458 J 6236 J
For air properties use online source: https://www.peacesoftware.de/einigewerte/luft_e.html The compressor is operating at steady-state increasing pressure of R-22 refrigerant from 4 bars to 14 bars. Temperature was rising during the process from 12C to 90C. The inlet volumetric flow rate is 1 m3/min and inlet diameter is 0.03m. At the exit the diameter is the same. Heat flow to the surroundings can be neglected. Determine: a.Mass flow rate [kg/s] SHOW AND EXPLAIN ALL STEPS PLEASE thanks