Steady-state creep rate data are gven here for some aloy taken at 200°C (473 K): , (h) a (MPa) 2.5x 10 55 2.3x 102 71 If it is known that the activation energy for creep is 160000 /mol, compute the steady state creep rate at a temperature of 220°C (493 K) and a stress level of 48 MPa. the tolerance is +/-9

Steady-state creep rate data are gven here for some aloy taken at 200°C (473 K): , (h) a (MPa) 2.5x 10 55 2.3x 102 71 If it is known that the activation energy for creep is 160000 /mol, compute the steady state creep rate at a temperature of 220°C (493 K) and a stress level of 48 MPa. the tolerance is +/-9

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) In the temperature range from 600°C to 750°C, a steel wire with 100 mm length shows the steady state creep behavior. The wire was exposed to 600°C under 300 MPa for ten years, how long the specimen would be? ( TH Trung Trong Stress (MPa) 1000 FTTinh Tru Trung Trung Trong th 800 600 400 200 100 80 60 40 815 C 20 d 10-6 104 10-5 650 C 730 C 925°C d d d d d 10-3 10-2 10-1 1 10 10² Steady-state creep rate (h-¹) 10³
QI/ If the thermal shock resistance of RBSN is 2214 w/m, poission ratio= 0.2 , cofficient of expansion= 2.6 x 10 /k, thermal conductivity=9 w/ m.k, specific heat= 0.86 j/ g.k ,thermal diffusivity= 4.4 x10 m /s, modulus of elasticity = 200 Gpa Calculate : 1.fracture streangth in Mpa 2. the density in Mpa 3. the thermal shock resistance in m' k/ s
5. Figure shows the cooling curve for aNiO-MgO ceramic. (e) the super heat; 2800 2700 2600 2525 2500 28 2400 10 20 30 40 50 Time (min) Temperature (°C)
A steel ruler of 40 cm, calibrated at 27°C, was used to measure a component in a relatively hot environment of 65°C. What would be the error % in the measurements if a .steel=17.7x10-6 °C^-1
A Tensile Tests of structural steel indicate that it fails whe the axial tensile strain is 1.80x10 μ. 3 Let maximum change in length that 0.25 [in] diamoren in tension car with stand before failure Length Find Structural Steel rad it It is 24 [in] in ni sa 9102
Consider the following data for a range of materials. In which of the following situations is creep likely to occur? Melting temperature of various materials: Melting Temperature (°C Material Ti alloy 1668 Carbon steel 1375 Alumina 2070 Nylon 66 polymer 262 A carbon steel component under continuous load in a power station operating at 200°C. A nylon pipe carrying fluid at 125K. All of the scenarios. A Ti alloy in a turbine operating at 350°C. An alumina ceramic component in a furnace operating at 600°C.
In a laboratory creep experiment at 1273K, a steady-state creep rate of 5 ××10-1 %, per hour is obtained in a metal alloy. The creep mechanism for this alloy is known to be dislocation climb with an activation energy of 200 kJ>mol. Predict the service temperature in (°C) for a creep rate of 8.68 ×10-5 %, per hour. (Assume that the laboratory experiment duplicated the service stress.)
Calculate the activation energy in J/mol for creep for an alloy having the steady state creep behavior shown in the figure. Use the data taken at stress level of 300MPa and temperature of 650C and 730C. Assume that the stress component n is independent of the temperature.
Please answer the question with steps An unknown material bar having length of 4.3m has 1m cross sectional area. One end is in contact with 373K Thermal conductivity of the material is 197W/mK. The total rate of heat flow is Joules/second. ....... .... (Calculate up to one decimal point accuracy).
8.35 Steady-state creep data taken for a stainless steel at a stress level of 70 MPa (10,000 psi) are given as follows: T(K) 10x 10 2.5 x 10 977 1089 If it is known that the value of the stress exponent n for this alloy is 7.0, compute the steady-state creep rate at 1250 K and a stress level of 50 MPa (7250 pst).
In an engineering application, the material is a strip of iron with a fixed crystallographic structure subject to a tensile load during operation. The part failed (yielded) during operation and needs to be replaced with a component with better properties. You are told that two other iron strips had failed at yield stresses of 110 and 120 MPa, with grain sizes of 30 microns and 25 microns respectively. The current strip has a grain size of 20 microns. The diameter of the rod is 1 mm and the load applied is 100 N. What is the yield stress of the new part C and would you recommend it for operation? Select one: a. O b. 129.5, yes C. 133.5 MPa, yes e. 120.5 MPa, no d. 140.5, no 123.5 MPa, yes
i need the answer quickly